Fetch Tx Time Alignment Data (4x4 MIMO configuration)

Returns the most recent Time Alignment measurement numeric results. This command may not be supported if your instrument is loaded with older firmware, in which case you may upgrade to the current firmware version or use the :FETCh:DEMod:TIMEalign? command, instead. Refer to your instrument User Guide for instructions on updating firmware.

Data are returned as 14 comma‑delimited values: EVM (rms) in %, EVM (pk) in %, Ref Signal (RS) Power in dBm, Sync Signal (SS) Power in dBm, Carrier Frequency in MHz, Freq Error in Hz, Freq Error in ppm, Cell ID, and Time Alignment Error (TAE) in nanoseconds for each of antenna pairs 1-2, 1-3, 1-4, 2-3, 2-4, and 3-4. “--” is returned for each data that is not valid at that instance.

Measurements, Modulation, Tx Time Alignment

Fetch Control Power Data

Returns the most recent Control Channel Power measurement numeric results.

Data are returned as 24 comma‑delimited values: RS_POWER, PSS_POWER, SSS_POWER, BCH_POWER, CFI_POWER, RS_TOTAL_POWER, PSS_TOTAL_POWER, SSS_TOTAL_POWER, BCH_TOTAL_POWER, CFI_TOTAL_POWER, TOTAL_POWER, TOTAL_CHANNEL_POWER

Measurements, Modulation, Control Channel Power

Fetch Constellation

Returns the constellation measurement numeric results of the demodulated data symbol over one sub‑frame measurement.

Data are returned as 10 comma‑delimited values: EVM (rms) in %, EVM (pk) in %, Ref Signal (RS) Power in dBm, Sync Signal (SS) Power in dBm, Carrier Frequency in MHz, Freq Error in Hz, Freq Error in ppm, Cell ID, the number of measurements used in the frequency error average (if on), and OSTP (OFDM Symbol Transmit Power) in dBm. “--” is returned for each data that is not valid at that instance.

Measurements, Modulation, Constellation

Fetch Power vs Resource Block Data

Returns the PVRB measurement results of the demodulated data.

Data are returned as a string of comma‑delimited values: Active RBs, Utilization in %, Channel Power in dBm, OSTP (OFDM Symbol Transmit Power) in dBm, EVM total in %, EVM (QPSK) in %, EVM (16‑QAM) in %, EVM (64‑QAM) in %, Cell ID.

If Option 886 is installed and activated on the instrument, a value for EVM (256‑QAM) in % is returned at the end of the PVRB data string. “--” is returned if the LTE carrier does not use 256‑QAM modulation scheme. This value does not immediately follow EVM (64‑QAM) in order to maintain backward compatibility with instruments where Option 886 is not installed.

Measurements, Modulation, Power vs Resource Block

Fetch Tx Time Alignment Data

Returns the most recent Time Alignment measurement numeric results.

Data are returned as nine comma‑delimited values: EVM (rms) in %, EVM (pk) in %, Ref Signal (RS) Power in dBm, Sync Signal (SS) Power in dBm, Carrier Frequency in MHz, Freq Error in Hz, Freq Error in ppm, Cell ID, and Time Alignment Error (TAE) in nanoseconds. “--” is returned for each data that is not valid at that instance.

Measurements, Modulation, Tx Time Alignment

Fetch OTA Carrier Aggregation (4x4 MIMO configuration)

Returns the result of the most recent Carrier Aggregation measurement numeric results. This command may not be supported if your instrument is loaded with older firmware, in which case you may upgrade to the current firmware version or use the :FETCh:OTA:CAGGregation? command, instead. Refer to your instrument User Guide for instructions on updating firmware.

Data are returned as 70 comma delimited values. The values consist of five sets of Component Carrier (CC) data, with each set containing 14 fields (CP, tx1 antenna, tx2 antenna, tx3 antenna, tx4 antenna, RS Power, RS Delta Power, SS Power, EVM(rms), EVM(pk), Freq Error, Freq Error (ppm), TAE (nS), and Cell ID). The data are in sequential CC order.

A field with “--” means the data was invalid. An inactive Component Carrier turnsshow N/A for the entire set of data.

Measurements, Over‑the‑Air, Carrier Aggregation

Fetch OTA Carrier Aggregation

Returns the result of the most recent Carrier Aggregation measurement numeric results. Data are returned as 60 comma delimited values.

The values consist of five sets of Component Carrier (CC) data with each set containing 12 fields (CP, tx1 antenna, tx2 antenna, RS Power, RS Delta Power, SS Power, EVM(rms), EVM(pk), Freq Error, Freq Error (ppm), TAE (nS), and Cell ID). The data are in sequential CC order.

A field with “--” means the data was invalid. An inactive Component Carrier turnsshow N/A for the entire set of data.

Measurements, Over‑the‑Air, Carrier Aggregation

Fetch OTA Coverage Mapping

Returns the most recent Coverage Mapping measurement results.

Data are returned as six sets of comma‑delimited values. Each set consists of: Cell ID, Group ID, Sector ID, S‑SS Power, RSRP, RSRQ, and SINR.

Following the six sets of data are a final value for the Dominance.

“‑‑” is returned for each data that is not valid at that instance.

Measurements, Over‑the‑Air, Mapping

Fetch OTA Scanner

Returns the most recent OTA Scanner measurement results.

Data are returned as six sets of comma‑delimited values. Each set consists of: Cell ID, Group ID, Sector ID, S‑SS Power, RSRP, RSRQ, and SINR.

Following the six sets of data are a final value for the Dominance.

“‑‑” is returned for each data that is not valid at that instance.

Measurements, Over‑the‑Air, Scanner

Fetch OTA Tx Test

Returns the most recent OTA Tx Text measurement results.

Data are returned as three sets of comma‑delimited values. Each set consists of: Cell ID, Group ID, Sector ID, S‑SS Power, RSRP, RSRQ, and SINR.

Following the three sets of data are an additional set of four numbers: Dominance, Antenna Count, Average Power, Delta Power.

“‑‑” is returned for each data that is not valid at that instance.

Measurements, Over‑the‑Air, Tx Test

Fetch Adjacent Channel Leakage Ratio

Returns the most recent adjacent channel leakage ratio measurement results. If the instrument is sweeping, it turnsnot return until the sweep is complete. Refer to :READ:RF:ACLR? for a description of the returned data.

dBm

Measurements, RF, ACLR

Fetch Spectral Emission Mask

Returns Spectral Emission Mask measurement results (Pass or Fail).

Measurements, RF, Spectral Emission Mask

Fetch RF Spectrum

Returns the most recent RF Spectrum measurement results. Data are returned as two comma‑delimited values: Channel Power in dBm and Occupied bandwidth measurement in MHz. “--” is returned for each data that is not valid at that instance.

Measurements, RF, Channel Spectrum

Fetch Summary

Returns the values displayed in a Summary measurement view. If the current display is not a summary screen, the return value is ‘N/A’. The return string is a comma-separated list of the values displayed on the screen, in the order they are listed from top to bottom. The list is preceded by the name of the summary view: “RF Summary,” “Modulation Summary,” or “LTE Summary”.

RF Summary, Channel Power in dBm, Occupied BW in MHz, Lower Adjacent Channel Power 2 in dBm, Lower Adjacent Channel Power 1 in dBm, Upper Adjacent Channel Power 1 in dBm, Upper Adjacent Channel Power 2 in dBm, Spectral Emission Mask (Pass or Fail).

Modulation Summary, Ref Signal (RS) Power in dBm, Sync Signal (SS) Power in dBm, EVM (rms) in %, EVM (QPSK) in %, EVM (16‑QAM) in %, EVM (64‑QAM) in %, Freq Error in Hz, Freq Error in ppm, Cell ID, PBCH Power in dBm.

If Option 886 is activated on the instrument, a value for EVM (256‑QAM) in % is returned at the end of the Modulation Summary data string. “--” is returned if the LTE carrier does not use 256‑QAM modulation scheme. This value does not immediately follow EVM (64‑QAM) in order to maintain backward compatibility with instruments where Option 886 is not installed.

LTE Summary, Freq Error in Hz, Occupied BW in MHz, Carrier Frequency in MHz, Channel Power in dBm, Ref Signal (RS) Power in dBm, Sync Signal (SS) Power in dBm, EVM (rms) in %, PBCH Power in dBm, PCFICH Power in dBm, Spectral Emission Mask (Pass or Fail).

When Option 886 is installed, 256‑QAM EVM measurement results are included in the calculation of EVM (rms) percentage value.

Measurements, RF, RF Summary

Measurements, Modulation, Modulation Summary

Measurements, LTE Summary