S331E, S332E, S361E, S362E Site Master™MS2711E, MS2712E, MS2713E Spectrum Master™MT8212E, MT8213E Cell Master™ Programming Manual : Mobile WiMAX Commands : [:SENSe] Subsystem
 
[:SENSe] Subsystem
The commands in this subsystem relate to device-specific parameters, not signal-oriented parameters.
[:SENSe]:BANDwidth|BWIDth[:RESolution] <index>
[:SENSe]:BANDwidth|BWIDth[:RESolution]?
Title
Resolution Bandwidth
Description
Sets the resolution bandwidth. The <index> argument is a 1-based index of the position of the desired bandwidth in the instrument’s current bandwidth list. The list can be displayed on the instrument by choosing the “BW” submenu button in the “Setup” menu. For example, if the desired bandwidth is the 3rd item on the list, then the value of the <index> argument would be 3.
The query form of this command will return the index of the currently selected bandwidth on the list. The Default is the 1st index in the bandwidth list.
Parameter
<index>
Default Value
The default bandwidth is 5 MHz which is the 1st index in the bandwidth list.
Front Panel Access
Setup, BW
[:SENSe]:DEMod:CONStln:REFPoints[:STATe] OFF|ON|0|1
[:SENSe]:DEMod:CONStln:REFPoints[:STATe]?
Title
Constellation Reference Points
Required Option
47
Description
Sets the display of the reference points for the various constellations on/off.
Parameter
OFF|ON|0|1
Parameter Type
<boolean>
Default Value
ON
Front Panel Access
Measurements, Demodulator, Constellation, Reference Points
[:SENSe]:FREQuency:CENTer <freq>
[:SENSe]:FREQuency:CENTer?
Title
Center Frequency
Description
Sets the center frequency. Note that changing the value of the center frequency will change the value of the coupled parameters Start Frequency and Stop Frequency. It may also change the value of the span.
Parameter
<freq>
Default Value
2.5 GHz
Default Unit
Hz
Range
0 Hz to 7.1 GHz
Front Panel Access
Freq, Center Freq
[:SENSe]:FREQuency:SIGStandard:CHANnel <number>
[:SENSe]:FREQuency:SIGStandard:CHANnel?
Title
Channel Selection
Description
Sets the channel number for the selected signal standard.
Parameter
<number>
Front Panel Access
Freq, Channel
[:SENSe]:FREQuency:SIGStandard:NAMe <string>
[:SENSe]:FREQuency:SIGStandard:NAMe?
Title
Signal Standard
Description
Selects the desired signal standard from the list. The <string> argument is the name
of the desired signal standard as displayed in the instrument’s current signal
standard list. The list can be displayed on the instrument by choosing the Signal Standard submenu button in the Freq menu. The list can also be downloaded remotely and viewed using Anritsu Master Software Tools. For example, if the desired Signal Standard is P-GSM 900 - Uplink, then the value of the <string> argument would be “P-GSM 900 - Uplink”.
The query form of this command will return the name of the currently selected Signal Standard on the list.
Parameter
<string>
Front Panel Access
Freq, Signal Standard
[:SENSe]:PFail <test set>
[:SENSe]:PFail?
Title
PASS/FAIL Test Selection
Description
Selects the active test set to be used in subsequent PASS/FAIL measurements. The <test set> value must correspond to a test set that is defined in the test set list. To view the list on the instrument, go into the “Measurement” menu, press the “Pass/Fail Mode” key, and then press the “Select Pass/Fail Test” submenu. Alternatively, the list can be retrieved remotely and viewed using the Anritsu Master Software Tools. The <test set> argument is a 1-based index of the position of the desired Pass/Fail test set in the instrument’s current Pass/Fail test set list. For example, if the desired Pass/Fail test is the 3rd item on the list, then the value of the <test set> argument would be 3.
When using the query form of the command, the return value is the currently selected test set number. If there is not a valid test set selected, the return value is “-1” (negative 1).
Parameter
<test set>
Related Command
:CONFigure PFail
Front Panel Access
Measurements, Pass/Fail Mode, Select Pass/Fail Test
[:SENSe]:POWer[:RF]:RANGe:AUTO OFF|ON|0|1
[:SENSe]:POWer[:RF]:RANGe:AUTO?
Title
Automatic Amplitude Range
Description
Sets the automatic amplitude range. Setting the value to ON or 1 will result in the amplitude range being coupled to the detected input signal level. Setting the value to OFF or 0 will result in the input attenuation being un-coupled from the input signal level. That is, changing the input signal level will not change the amplitude range. When this command is issued, the amplitude range itself will not change. The default value is ON. That is, sending :SENS:POW:RANG:AUTO is equivalent to sending :SENS:POW:RANG:AUTO ON.
Parameter
OFF|ON|0|1
Parameter Type
<boolean>
Default Value
ON
Related Command
[:SENSe]:POWer[:RF]:RANGe
Front Panel Access
Amplitude, Auto Range
[:SENSe]:POWer[:RF]:RANGe[:IMMediate]
Title
Amplitude Range
Description
Re-calculates amplitude range. Note that issuing this command will set the automatic dynamic range OFF.
Related Command
[:SENSe]:POWer[:RF]:RANGe:AUTO
Front Panel Access
Amplitude, Adjust Range
[:SENSe]:RF:SPECtrum:SPAN 5|10|20|30
[:SENSe]:RF:SPECtrum:SPAN?
Title
Spectrum View Span
Description
Sets the span for the Spectrum view. Setting the value to 5 will set the span for the Spectrum view to 5 MHz. Setting the value to 10 will set the span for the Spectrum view to 10 MHz. Setting the value to 20 will set the span for the Spectrum view to 20MHz. Setting the value to 30 will set the span for the Spectrum view to 30MHz.
Parameter
5|10|20|30
Default Value
10 MHz
Default Unit
MHz
Front Panel Access
Measurements, RF Measurements, Spectrum, Span