CW Frequency

Sets the frequency for the Generator in CW Mode.

1 GHz

0 Hz to 3 GHz (MS2711E) or 4 GHz (MS2712E) or 6 GHz (MS2713E)

Hz

To set CW frequency at 2 GHz

Shift-4 (Measure), Generator, Generator Mode CW, CW Frequency

Generator Mode

Toggle Generator Mode between CW and Tracking.

Note: This command does not turn the generator on. Refer to :INITiate:GENerator

CW|TRACking

CW

To select Tracking Generator Mode:

Shift-4 (Measure), Generator, Generator Mode

 

Enhanced Accuracy Calibration

Improves the output accuracy of the generator. The calibration can be done in both Tracking Generator and CW Generator modes. Changing the output power turns enhanced calibration OFF. Use [:SENSe]:ENhanced:CALibration:COMPlete[:STATe]? to determine when calibration is complete. Calibration may take 2 to 4 minutes to complete.

Note: The Enhanced Accuracy calibration is eliminated when the calibration is turned off (:GEN:EN:CAL OFF), at Preset, at Power-on, or when the generator output level is changed. The calibrations are not saved nor recalled with Save/Recall.

OFF|ON|0|1

OFF

To turn Enhanced Accuracy Calibration ON

Shift-4 (Measure),Generator, Settings, Enhanced Generator Power Accuracy, Enhanced Accuracy Calibration

Calibration Completion State

Queries the state of the enhanced accuracy/additional calibration. This is used with enhanced accuracy calibration and additional calibration to determine the state of the calibration. If 0 is returned, calibration is in progress, -1 indicates failure, 1 indicates completion and 2 indicates failure to start calibration because additional calibration sweep was selected before turning Enhanced Accuracy Calibration ON.

0, -1, 1, 2

n/a

Number of External 3 dB Pads

Calibration accuracy can be improved by adding one or two 3 dB pads. This command selects the number of pads added. This is done before turning ON the Enhanced Accuracy Calibration or performing an Additional Calibration Sweep.

0|1|2

2

0 to 2

If one 3 dB pad is connected on the receiver:

Shift-4 (Measure), Generator, Settings, Enhanced Generator Power Accuracy, Matching Pads(3dB)

Tracking Generator Absolute Power Statistic State

Specifies whether the tracking generator absolute power statistic table is ON or OFF. If the value is set to ON or 1, the tracking generator absolute statistic table is turned on.If the value is set to OFF or 0, the tracking generator absolute statistic table is turned off.

The query version of the command returns a 1 if the tracking generator absolute power statistic is on and returns a 0 if the tracking generator power statistic is off.

Note that this command is ignored if the tracking generator output is off.

OFF|ON|0|1

<boolean>

OFF

To turn off the generator absolute power statistics:

Shift-4 (Measure), Generator, Settings, Power Statistics

Tracking Generator Normalize State

(Only valid for Tracking Mode and Normalize On) Specifies whether the tracking generator transmission statistic is ON or OFF. If the value is set to ON or 1, the tracking generator transmission statistic is turned on. Turning on normalization triggers the normalization sweep, during which the sweep complete bit of the operation status is zero, and :STATus:OPERation? can be used to detect the completion of the normalization sweep. If the value is set to OFF or 0, the tracking generator normalization is turned off.

The query version of the command returns a 1 if the tracking generator normalization is on and returns a 0 if the tracking generator normalization is off.

Note that this command is ignored if the tracking generator output is off.

OFF|ON|0|1

<boolean>

OFF

To turn off the tracking generator normalized state:

Shift-4 (Measure), Generator, Transmission Measurement, Normalize

Tracking Generator Scale

(Only valid for Tracking Mode) Sets the tracking generator relative scale (dB/division) in Transmission measurements.

10 dB/div

1 dB to 15 dB

dB

Shift-4 (Measure), Generator, Transmission Measurement, Relative Scale

Tracking Generator Reference Level

(Only valid for Tracking Mode) Sets the tracking generator relative reference level amplitude value for the y-axis in Transmission measurements.

10 dB (50 dB after Normalize is turned on)

Current active amplitude unit

[:SENSe]:TGENerator:TX[:SCALe]:RLEVel:OFFSet <rel ampl>

Shift-4 (Measure), Generator, Transmission Measurement, Relative Ref

(Only valid for Tracking Mode and Normalize On) Tracking Generator Reference Level Offset

Sets the tracking generator reference level offset value for the y-axis in Transmission measurements.

0 dB

-100 dB to 100 dB

dB

Shift-4 (Measure), Generator, Transmission Measurement, Transmission Offset

Tracking Generator Transmission Statistic State

(Only valid for Tracking Mode and Normalize On) Specifies whether the tracking generator transmission statistic is ON or OFF. If the value is set to ON or 1, the tracking generator transmission statistic is turned on. If the value is set to OFF or 0, the tracking generator transmission statistic is turned off.

The query version of the command returns a 1 if the tracking generator transmission statistic is on and returns a 0 if the tracking generator is off.

Note that this command is ignored if the tracking generator normalization is off.

OFF|ON|0|1

<boolean>

OFF

To turn on the tracking generator transmission statistic state:

Shift-4 (Measure), Generator, Transmission Measurement, Transmission Statistics