ACPR Adjacent Channel Bandwidth

Sets the adjacent channel bandwidth for the ACPR measurement.

<freq>

10.35 MHz

Hz

Shift‑4 (Measure), Power and Bandwidth, ACPR, Adj/Alt Ch BW

ACPR Main Channel Bandwidth

Sets the main channel bandwidth for the ACPR measurement.

<freq>

10.35 MHz

Hz

Shift‑4 (Measure), Power and Bandwidth, ACPR, Main Ch BW

ACPR Channel Spacing

Sets the channel spacing for the ACPR measurement.

<freq>

10.35 MHz

Hz

Shift‑4 (Measure), Power and Bandwidth, ACPR, Ch Spacing

ACPR Measurement State

Sets the state of the adjacent channel power ratio measurement, ON or OFF. When using :CONFigure:ACPower, the state is automatically set to ON.

OFF|ON|0|1

<boolean>

OFF

Number of Traces to Average

Sets the number of traces to average.

<integer>

<integer>

10

2 to 65535

Shift‑5 (Trace), Trace A Operations, # of Averages

Trace Mode (Normal/Average/Max Hold/Min Hold)

Specifies how successive traces are combined to produce the resulting display value. Setting the TYPE to NONE is the equivalent of setting the trace mode to “Normal->A” on the front panel. The displayed value for a point is the current measured value for that point. Setting the TYPE to SCALar is the equivalent of setting the trace mode to “Average->A” on the front panel. The displayed value for a point is the average of the last <integer> measured values where <integer> is set by [:SENSe]:AVERage:COUNt. Setting the TYPE to MAXimum is the equivalent of setting the trace mode to “Max Hold->A” on the front panel. The displayed value for a point is the maximum measured value for that point over sweeps. Setting the TYPE to MINimum is the equivalent of setting the trace mode to “Min Hold->A” on the front panel. The displayed value for a point is the minimum measured value for that point over sweeps.

NONE|SCALar|MAXimum|MINimum

<char>

NONE

To set the TYPE to SCALar:

To set the TYPE to MAXimum:

Shift‑5 (Trace), Trace A Operations

Video Bandwidth

Sets the video bandwidth. Note that using this command turns the automatic video bandwidth setting OFF.

<freq>

1 MHz

Hz

1 Hz to 3 MHz in a 1:3 sequence except for the MS2711E
10 Hz to 3 MHz in a 1:3 sequence for the MS2711E

BW, VBW

Video Bandwidth Coupling

Sets the state of the coupling of the video bandwidth to the resolution bandwidth. Setting the value to ON or 1 will result in the video bandwidth being coupled to the resolution bandwidth. That is, when the resolution bandwidth changes, the video bandwidth changes. Setting the value to OFF or 0 will result in the video bandwidth being un-coupled from the resolution bandwidth. That is, changing the resolution bandwidth will not change the video bandwidth. When this command is issued, the video bandwidth setting itself will not change. The default value is ON. That is, sending :SENS:BAND:VID:AUTO is equivalent to sending :SENS:BAND:VID:AUTO ON.

OFF|ON|0|1

<boolean>

ON

BW, Auto VBW

Video Bandwidth to Resolution Bandwidth Ratio

Sets the ratio of the video bandwidth to the resolution bandwidth for use when the video to resolution bandwidth coupling is enabled. Note that the front panel interface sets the inverse ratio: the resolution bandwidth to the video bandwidth which is an integer, in other words, if you send 0.35, the display will show 2 not 2.857.

<number>

0.33

0.00001 to 1

BW, RBW/VBW (note that this is the inverse ratio)

Resolution Bandwidth

Sets the resolution bandwidth. Note that using this command turns OFF the automatic resolution bandwidth setting.

<freq>

3 MHz

Hz

1 Hz to 3 MHz in a 1:3 sequence except for the MS2711E
100 Hz to 3 MHz in a 1:3 sequence for the MS2711E

BW, RBW

Resolution Bandwidth Coupling

Sets the state of the coupling of the resolution bandwidth to the frequency span. Setting the value to ON or 1 will result in the resolution bandwidth being coupled to the span. That is, when the span changes, the resolution bandwidth changes. Setting the value to OFF or 0 will result in the resolution bandwidth being un-coupled from the span. That is, changing the span will not change the resolution bandwidth. When this command is issued, the resolution bandwidth setting itself will not change. The default value is ON. That is, sending :SENS:BAND:RES:AUTO is equivalent to sending :SENS:BAND:RES:AUTO ON.

OFF|ON|0|1

<boolean>

ON

BW, Auto RBW

Resolution Bandwidth to Span Ratio

Sets the ratio of the resolution bandwidth to the span for use when the resolution bandwidth to span coupling is enabled. Note that the front panel interface sets the inverse ratio: the span to the resolution bandwidth.

<number>

0.01

0.00001 to 1

BW, Span/RBW (note that this is the inverse ratio)

Channel Power Integration Bandwidth

Sets the integration bandwidth for the channel power measurement. Integration bandwidth must be less than or equal to the frequency span.

<freq>

10.35 MHz

Hz

Shift‑4 (Measure), Power and Bandwidth, Channel Power, Ch Pwr Width

Channel Power Measurement State

Sets the state of the channel power measurement, ON or OFF. When using :CONFigure:CHPower, the state is automatically set to ON.

OFF|ON|0|1

<boolean>

OFF

Shift‑4 (Measure), Power and Bandwidth, Channel Power, On/Off

Other Input Impedance Loss

Sets the value that is used for amplitude correction when the value set by [:SENSe]:CORRection:IMPedance[:INPut][:MAGNitude] is something other than 50 or 75. This value is not applied if the impedance is set to either 50 or 75.

<rel ampl>

0

dB

0 dB to 100 dB

Shift‑8 (System), Application Options, Impedance

Input Impedance

Sets the input impedance that is used for amplitude correction and conversion between units (dBm vs. dBV vs. Volts, etc.). If the value of <integer> is 50 no correction is performed. If the value of <integer> is 75 correction is done based on Anritsu adapter 12N50-75B.

<integer>

<integer>

50

50, 75 all other values are treated as described above

Shift‑8 (System), Application Options, Impedance

Detection Type

Sets the detection method for calculating each display point. Each display point represents several measurements. The detection type determines how the display point is derived from its associated measurements. POSitive Peak detection displays the maximum value of the associated measurements. RMS detection displays the average power of the associated measurements. NEGative Peak detection displays the minimum value of the associated measurements. SAMPle detection displays the “middle” point of those measurements associated with a display point. For example, if there are 3 measurement frequencies associated with a given display point, sample detection will display the value at the frequency of the second measurement point.

POSitive|RMS|NEGative|SAMPle

<char>

(Positive) Peak

Amplitude, Detection

EMF State

Switches EMF ON or OFF.

The query form of this command returns a 0 or 1 when EMF state is OFF or ON, respectively.

Note: EMF will turn ON only if the start and stop frequencies are within the frequency range of the spectrum analyzer and isotropic antenna used. The antenna must be connected.

OFF|ON|0|1

<boolean>

OFF

Shift‑4 (Measure), Power and Bandwidth, EMF Measurement, On/Off

Frequency Reference Status

Returns 0 for internal or GPS reference. Returns 1 for external reference.

None

Center Frequency

Sets the center frequency. Note that changing the value of the center frequency will change the value of the coupled parameters Start Frequency and Stop Frequency. It may also change the value of the span.

<freq>

Hz

Freq, Center Freq

Channel Selection

Sets the channel number for the selected signal standard.

<number>

Freq, Channel

Signal Standard

Selects the desired signal standard from the list. The <string> argument is the name of the desired signal standard as displayed in the instrument’s current signal standard list. The list can be displayed on the instrument by choosing the Signal Standard submenu button in the Freq menu. The list can also be downloaded remotely and viewed using Anritsu Master Software Tools. For example, if the desired Signal Standard is P-GSM 900 - Uplink, then the value of the <string> argument would be “P-GSM 900 - Uplink”.

The query form of this command will return the name of the currently selected Signal Standard on the list.

<string>

Freq, Signal Standard

Frequency Span

Sets the frequency span. Setting the value of <freq> to 0 Hz is the equivalent of setting the span mode to zero span. Note that changing the value of the frequency span will change the value of the coupled parameters Start Frequency and Stop Frequency and may change the Center Frequency.

<freq>

Hz

Frequency Span – Full

Sets the frequency span to full span. Note that changing the value of the frequency span will change the value of the coupled parameters, Start Frequency and Stop Frequency and may change the Center Frequency.

Span, Full Span

Frequency Span – Last

Sets the frequency span to the previous span value. Note that changing the value of the frequency span will change the value of the coupled parameters, Start Frequency and Stop Frequency and may change the Center Frequency.

Hz

Span, Last Span

Start Frequency

Sets the start frequency. Note that in the spectrum analyzer, changing the value of the start frequency will change the value of the coupled parameters, Center Frequency and Span.

<freq>

0 Hz

Hz

Freq, Start Freq

Frequency Step

Sets the frequency step to the given frequency value.

<freq>

1 MHz

Hz

1 Hz to 20 GHz

Freq, Step Size & Offset, Freq Step

Stop Frequency

Sets the stop frequency. Note that in the spectrum analyzer, changing the value of the stop frequency will change the value of the coupled parameters, Center Frequency and Span.

<freq>

Hz

Field Strength Antenna

Selects an antenna from the antenna list to use for field strength measurement result calculations. The <antenna> argument is a 1-based index of the position of the desired antenna in the instrument’s current antenna list. The list can be displayed on the instrument by choosing the “Antenna” submenu button in the “F Strength” menu. For example, if the desired antenna were the 3rd item on the antenna listing, then the value of the <antenna> argument would be 3.

The <antenna> value for EMI antenna list starts from 65.

The query form of this command will return the index of the currently selected antenna.

<antenna>

1

Shift‑4 (Measure), Power and Bandwidth, Field Strength, Antenna

Field Strength Measurement State

Sets the state of the field strength measurement, ON or OFF. When using :CONFigure:FSTRength, the state is automatically set to ON.

OFF|ON|0|1

<boolean>

OFF

Shift‑4 (Measure), Power and Bandwidth, Field Strength, On/Off

Occupied Bandwidth Measurement Method

Sets the method for calculating occupied bandwidth. XDB calculates the occupied bandwidth based on points a specified number of dB below the carrier. Issue command [:SENSe]:OBWidth:XDB to set the number of dB to be used. PERCent calculates the occupied bandwidth based on points a specified percentage of the carrier power below the carrier. Issue command [:SENSe]:OBWidth:PERCent to set the percentage to be used.

XDB|PERCent

<char>

PERCent

Shift‑4 (Measure), Power and Bandwidth, OCC BW

Occupied Bandwidth Percent of Power

This command sets the percentage of carrier power used to measure the occupied bandwidth. This value is used in the measurement if :SENSe:OBWidth:METHod is set to PERCent.

<percentage>

99

%

0% to 100%

Shift‑4 (Measure), Power and Bandwidth, OCC BW, %

Occupied Bandwidth Measurement State

Sets the state of the occupied bandwidth measurement, ON or OFF. When using :CONFigure:OBWidth, the state is automatically set to ON.

OFF|ON|0|1

<boolean>

OFF

Shift‑4 (Measure), Power and Bandwidth, OCC BW, On/Off

Occupied Bandwidth dB Down

This command sets the number of dB below the carrier used to measure the occupied bandwidth. This value is used in the measurement if :SENSe:OBWidth:METHod is set to XDB.

<rel ampl>

3 dBc

dBc

0 to 100 dBc

Shift‑4 (Measure), Power and Bandwidth, OCC BW, dBc

IF Bandwidth State

Sets the IF Bandwidth. Setting a value of 1 is equivalent of setting the IF Bandwidth to Normal on the front panel. Setting a value of 3 is equivalent of setting the IF Bandwidth to 10 MHz BW on the front panel. Setting the value of 4 is equivalent of setting the IF Bandwidth to 16 MHz BW on the front panel. Note that option 89 must be available and in Zero span for the command to be valid. The query version of this command will return a 0 if not in zero span.

1|2|3|4|5

1|2|3|4|5

Input Attenuation

Sets the input attenuation. Note that issuing this command will set the automatic input attenuation OFF.

<rel ampl>

30 dB

dB

0 dB to 65 dB

Amplitude, Atten Lvl

Input Attenuation Coupling

Sets the input attenuation coupling. Setting the value to ON or 1 will result in the input attenuation being coupled to the reference level. Setting the value to OFF or 0 will result in the input attenuation being un-coupled from the reference level. That is, changing the reference level will not change the input attenuation. When this command is issued, the input attenuator setting itself will not change. The default value is ON. That is, sending :SENS:POW:ATT:AUTO is equivalent to sending :SENS:POW:ATT:AUTO ON.

OFF|ON|0|1

<boolean>

ON

Amplitude, Auto Atten

Preamp State

Sets the state of the preamp. Note that this may cause a change in the reference level and/or attenuation.

Note: The MS2711E returns a value of -1 if Preamp (Option 8) is not installed.

OFF|ON|0|1

<boolean>

OFF

Amplitude, Pre Amp

Sweep Mode

Sets the sweep mode to Fast, Performance or No FFT. The query from of this command returns the current sweep mode short form.

Note: FAST Sweep Mode is not available for the MS2711E.

FAST|PERFormance|NOFFt

<char>

Shift‑3 (Sweep), Sweep Mode

Sweep Status

Returns 1 when the sweep is complete. Returns 0 when the sweep is in progress.

None

Minimum Sweep Time

Sets the value of the minimum sweep time parameter. The sweep will complete in the shortest time possible. To sweep as fast as possible, enter the minimum value allowed for the sweep time.

0.001

Seconds

10 μs to 600000000 μs

Shift‑3 (Sweep), Sweep Time

Actual Sweep Time

Returns the actual sweep time as opposed to the specified sweep time.

Seconds

Auto Sweep Time

Sets Auto Sweep Time on or off.

Shift‑3 (Sweep), Auto Sweep Time

Trace Count

Returns a string with two integers representing the current trace’s average count and the total number of trace averages.

None