:CALCulate:MARKer Subsystem

This subsystem contains commands to manipulate data markers.

Turn All Markers Off

:CALCulate:MARKer:AOFF

Turns off all markers.

Front Panel Access:

VNA: Marker, All Markers Off SPA: Marker, More, All Markers Off WCDMA: Marker, All Markers Off

 

Delta Marker State

:CALCulate:MARKer[1]|2|3|4|5|6:DELTa[:STATe] OFF|ON|0|1

:CALCulate:MARKer[1]|2|3|4|5|6:DELTa[:STATe]?

Sets the specified delta marker on/off.

Factory Preset / *RST:	OFF
Front Panel Access:	Marker, Delta

 

Delta Marker X Value

:CALCulate:MARKer[1]|2|3|4|5|6:DELTa:X <x-parameter>

:CALCulate:MARKer[1]|2|3|4|5|6:DELTa:X?

Sets the location of the delta marker on the x-axis at the specified location <x-parameter> + the reference marker x-axis. <x-parameter> is defined in the current x-axis units.

The query version of the command returns the location of the delta marker on the x-axis.

Default Unit:	Current x-axis unit
Front Panel Access:	Marker, Delta
See Also:	:CALCulate:MARKer[1]|2|3|4|5|6:X

 

Delta Marker Read Y Value

:CALCulate:MARKer[1]|2|3|4|5|6:DELTa:Y?

Reads the current Y value for the specified delta marker. The units are the units of the y-axis.

Default Unit:

Current y-axis unit

 

Marker (Maximum) Peak Search

:CALCulate:MARKer[1]|2|3|4|5|6:MAXimum

Puts the specified marker at the maximum amplitude in the trace.

Front Panel Access:

Marker, [Marker 1/2/3/4/5/6,] Peak Search Marker, More Peak Options, Peak Search

 

Marker (Maximum) Peak Search Left

:CALCulate:MARKer[1]|2|3|4|5|6:MAXimum:LEFT

Puts the specified marker on the next highest peak to the left of the current peak.

The next highest peak must be above the peak threshold. If no point meets that criterion, the marker is set to the first point on the trace. Note that this command is valid only if the specified marker is on.

Front Panel Access:	Marker, More Peak Options, Next Peak Left
See Also:	:CALCulate:MARKer:PEAK:THReshold

 

Marker (Maximum) Peak Search Right

:CALCulate:MARKer[1]|2|3|4|5|6:MAXimum:RIGHt

Puts the specified marker on the next highest peak to the right of the current peak.

The next highest peak must be above the peak threshold. If no point meets that criterion, the marker is set to the last point on the trace. Note that this command is valid only if the specified marker is on.

 

Front Panel Access:	Marker, More Peak Options, Next Peak Right
See Also:	:CALCulate:MARKer:PEAK:THReshold

 

Peak Threshold

:CALCulate:MARKer:PEAK:THReshold <percentage>

:CALCulate:MARKer:PEAK:THReshold?

Sets the peak/valley threshold as a percentage of the display.

:CALCulate:MARKer:MAXimum:LEFT and :CALCulate:MARKer:MAXimum:RIGHt use this value to determine whether a particular display point qualifies as a peak.

 

Factory Preset / *RST:	10%
Range:	0% to 100%
Default Unit:	%
Front Panel Access:	Marker, More Peak Options, Peak Threshold

 

Marker Frequency to Center

:CALCulate:MARKer[1]|2|3|4|5|6[:SET]:CENTer

Sets the center frequency equal to the frequency of the specified marker.

Note that this will result in a change to the start and stop frequencies and may also result in a change to the span.

Front Panel Access:

Marker, Marker Freq to Center

 

Marker to Reference Level

:CALCulate:MARKer[1]|2|3|4|5|6[:SET]:RLEVel

Sets the reference level equal to the measured amplitude of the specified marker.

Note that this may result in a change to the input attenuation.

Front Panel Access:

Marker, Marker to Ref Lvl

 

Marker State

:CALCulate:MARKer[1]|2|3|4|5|6[:STATe] OFF|ON|0|1

:CALCulate:MARKer[1]|2|3|4|5|6[:STATe]?

Sets the specified marker on/off.

Factory Preset / *RST:	OFF
Front Panel Access:	Marker, On/Off

 

Marker X Value

:CALCulate:MARKer[1]|2|3|4|5|6:X <x-parameter>

:CALCulate:MARKer[1]|2|3|4|5|6:X?

Sets the location of the marker on the x-axis at the specified location. <x-parameter> is defined in the current x-axis units.

The query version of the command returns the location of the marker on the x-axis.

Default Unit:	Current x-axis unit
Front Panel Access:	Marker, [Marker 1/2/3/4/5/6]

 

Marker Read Y Value

:CALCulate:MARKer[1]|2|3|4|5|6:Y?

Reads the current Y value for the specified marker. The units are the units of the y-axis.

Default Unit:

Current y-axis unit

 

Copyright 2011 Anritsu Company
	Anritsu Company
	1800-ANRITSU
	10450-00034, Rev. A
	mmdtechpubs@anritsu.com