Antenna information invalid. Attach directional antenna or switch to manual.
In Title bar, Not Logged, Persistent
Battery Fault
In Title bar, Logged, Transient
Battery level is critically low. Automatic shutdown is imminent
Popup, Logged, Persistent
Battery level low
Popup, Logged, Persistent
Battery Low warning
Pop-up Window, Logged, Persistent: Requires User Intervention
This message is sent once per low battery charge condition per boot cycle per charge cycle. A low battery charge condition is defined as the battery charge being at or below 10%.
Booted from backup SW slot. Reinstall SW to clear this message
Popup, Logged, Persistent
Could not read from input file. Please verify that the storage device is still accessible and try again
In Title bar, Not Logged, Transient
Could not create output file. Please verify that the device is accessible and can be written to
In Title bar, Not Logged, Transient
Cannot verify data integrity
In Toolbar, Not Logged, Transient
Channel Scanner CSV file failed to open
In Title bar, Logged, Transient
Current settings do not allow for simultaneous sweep and audio output
In Title bar, Not Logged, Persistent
Device transfer speed insufficient for gapless transfer at current BW/bit depth settings; some samples will be missed
In Title bar, Logged, Persistent
Error occurred during concatenation. Error code: <code>
Popup, Not Logged, Transient
Failed to recall limit
When the limit setup file selected for recall could not be accessed.
Failed to save file: filename
When any other error occurred while trying to save a file.
Failed to save screenshot. Device may be full.
When saving a screenshot fails.
IF Gain Calibration is off
In Title bar, Logged, Persistent
IF Shape Calibration is off
In Title bar, Logged, Persistent
Invalid frequency setup for this antenna
In Title bar, Logged, Transient
Limit recall initiated
When a limit setup file is selected for recall.
Maximum number of measurement points have been reached. To continue, save and clear current measurement points and start again.
In Title bar, Not Logged, Persistent
Not enough available space to save file: <filename>
When the entire file could not be written.
One or more shortcuts are no longer valid: <shortcut name>. File (s) cannot be found.
In Title bar, Logged, Persistent
Playback file corrupted, stopping playback
In Title bar, Logged, Transient
RBW changed: cannot be greater than IF bandwidth
In Title bar, Logged, Transient
Recall file does not exist
When the file selected for recall could not be accessed
Record CSV file failed to open
In Title bar, Logged, Transient
Reference Level Calibration is off
In Title bar, Logged, Persistent
Remote Lockout Warning: Warning Instrument Is Under Remote Control. Press “Return to Local” to exit remote control and enable on-screen
Popup, Not Logged, Persistent
Restart required for new settings to take effect.
Persistent. When hostname or options (in the Debug menu) are changed.
RF or Reference Level must be below <value> to enable PreAmp
In Title bar, Logged, Transient
Setting change detected; unloading playback file
In Title bar, Logged, Transient
Selected points is not valid with calibration applied, setting to nearest Cal point.
In Title bar, Logged, Transient
Save failed. File size exceeds save limits. Adjust setup and try again
In Title bar, Logged, Transient
Shutdown Battery Level Reached
Pop-up Window, Logged, Persistent: Requires User Intervention
Sent after a Battery Low warning. A shutdown will occur when the battery charge is or below 5%.
Shutdown Temperature Reached
Popup, Logged, Persistent
Simulated Test Signal data being displayed
In Title bar, Logged, Persistent
Spectrogram view not available
In Title bar, Logged, Transient
Segment gate length too short. Increase RBW or VBW setting for segments (X)
In Title bar, Logged, Persistent. X indicates the incorrect segments.
SSB frequency exceeds channel bandwidth
In Title bar, Not Logged, Persistent
TDD UL/DL common configuration invalid
In Title bar, Logged, Persistent
Temperature High Warning
In Title bar, Logged, Persistent
Triangulation line limit reached
In Title bar, Logged, Transient
The selected mode is not yet available.
When an unavailable mode is selected.
The ALC Cal Data is incorrect for the attached microwave module
In Title bar, Logged, Persistent
The following options will expire in less than 24 hours <Option Number>. Reboot required. The system will reboot at X.
In Title bar, Logged, Persistent. X denotes the date and time.
The following options have expired <Option Number>. Reboot required. The system will reboot at X
Popup, Logged, Transient. X denotes the date and time.
The following options have expired <Option Number>
In Title bar, Logged, Transient
The following options have expired <Option Number>
Popup, Logged, Transient
Quasi-peak detection selected. Sweep will be slower
In Title bar, Logged, Transient
Zero Span is not available
In Title bar, Logged, Transient
<Name of setting> <Value of setting> exceeds the min/max range <minimum value - maximum value>
In Title bar, Logged, Transient
<setting> value change is not allowed with calibration applied
In Title bar, Logged, Transient
Setting change is not allowed while a calibration is in progress
In Title bar, Logged, Transient
Setting change is not allowed with flex calibration