VNA Master™Programming Manual : Spectrum Analyzer Commands
 
Spectrum Analyzer Commands
 
Introduction
Spectrum Analyzer Commands
:ABORt Subsystem
:CALCulate Subsystem
Limit Alarm
Limit Fail
Lower Limit Fail State
Limit Pass/Fail
Upper Limit Fail State
Move Limit to Current Center Frequency
Create Limit Envelope
Limit Envelope Offset
Number of Limit Envelope Points
Limit Envelope Shape
Update Limit Envelope Frequency
Update Limit Envelope Amplitude
Limit Fail State
Lower Limit Alarm
Lower Limit Fail State
Number of Lower Limit Points
Lower Limit State
Limit Line Type
Limit Mirror
Add Limit Point
Delete Limit Point
Next Point Left
Next Point Right
Limit Point X Value
Limit Point Y Value
Number of Limit Points
Set Limit Line Upper or Lower
Upper Limit Alarm
Upper Limit Fail State
Number of Upper Limit Points
Upper Limit State
Move Limit
Add Vertical
Limit X Value
Limit Line Y Value
Set Default Limit
Limit State
Turn All Markers Off
Peak Threshold
Marker Data
Marker Table State
Marker Noise
Delta Marker X Value
Delta Marker Read Y Value
Delta Marker to Span
Delta Marker State
Marker Counter
Marker Fixed State
Marker (Maximum) Peak Search
Marker (Maximum) Peak Search Left
Marker (Maximum) Peak Search Next
Marker (Maximum) Peak Search Right
Marker Noise
Marker X Value
Marker Read Y Value
Marker Frequency to Center
Marker to Reference Level
Marker State
:CONFigure Subsystem
Configure Adjacent Channel Power Ratio
Configure Channel Power
Configure Field Strength
Configure Occupied Bandwidth
Measurement Mode
:DISPlay Subsystem
Display Grid
Auto Reference Level
Scale
Reference Level
Reference Level Offset
:FETCh Subsystem
Fetch Adjacent Channel Power Ratio
Fetch Channel Power
Fetch Channel Power Density
Fetch Channel Power/Density
Fetch Occupied Bandwidth Frequency
Fetch Occupied Bandwidth
:FORMat Subsystem
Numeric Data Format
:INITiate Subsystem
Continuous/Single Sweep
Trigger Sweep/Measurement
Save On Crossing Limit
Save On Sweep Complete
Save Then Stop
:MEASure Subsystem
Measure Adjacent Channel Power Ratio
Measure Channel Power
Measure Channel Power Density
Measure Channel Power/Density
Measure Occupied Bandwidth
:MMEMory Subsystem
Transfer Data
Delete Setup/Measurement
Recall Limit
Recall Setup
Recall Measurement
Save Limit
Save Setup
Save Measurement
:READ Subsystem
Read Adjacent Channel Power Ratio
Read Channel Power Density
Read Channel Power
Read Occupied Bandwidth
:TRACe Subsystem
Trace Copy
Trace Exchange
Trace Header Transfer
Trace Header Parameters
Trace Data Transfer
Trace View State
Trace Write State
Trace A Operation
Trace B Operation
Trace C Operation
:TRIGger Subsystem
Trigger Source
Video Trigger Level
Video Trigger Position
:UNIT Subsystem
Measurement Units
[:SENSe] Subsystem
ACPR Adjacent Channel Bandwidth
ACPR Main Channel Bandwidth
ACPR Channel Spacing
ACPR Measurement State
Number of Traces to Average
Trace Mode (Normal/Average/Max Hold/Min Hold)
Resolution Bandwidth
Resolution Bandwidth Coupling
Resolution Bandwidth to Span Ratio
Video Bandwidth
Video Bandwidth Coupling
Video Bandwidth to Resolution Bandwidth Ratio
Channel Power Integration Bandwidth
Channel Power Measurement State
Input Impedance
Other Input Impedance Loss
Detection Type
Frequency Reference Status
Center Frequency
Channel Selection
Signal Standard
Frequency Span
Frequency Span – Full
Frequency Span – Last
Start Frequency
Frequency Step
Stop Frequency
Field Strength Antenna
Field Strength Measurement State
Occupied Bandwidth Measurement Method
Occupied Bandwidth Percent of Power
Occupied Bandwidth Measurement State
Occupied Bandwidth dB Down
Input Attenuation
Input Attenuation Coupling
Preamp State
Sweep Status
Minimum Sweep Time
Trace Count
Introduction
This chapter describes commands for Spectrum Analyzer mode. Only the commands that are listed in this chapter and in All Mode Commands can be used in Spectrum Analyzer mode. Using commands from other modes may produce unexpected results.
Notational conventions are described in Command and Query Notational Conventions.
Spectrum Analyzer Commands
SPA Commands Subsystems
Keyword
Parameter Data or Units
:ABORt
:CALCulate
:CONFigure
:DISPlay
:FETCh
:FORMat
:INITiate
:MEASure
:MMEMory
:READ
:SENSe
:TRACe
:TRIGger
:UNIT
[:SENSe]