VectorStar™ MS464xB Series Microwave Vector Network Analyzer Programming Manual : SCPI Commands : :SENSe{1-16}:FREQuency Subsystem
 
:SENSe{1-16}:FREQuency Subsystem
The :SENSe{1-16}:FREQuency subsystem commands control the various instrument frequencies on a channel-by-channel basis.
Channel and Sweep Subsystems
Related channel and sweep configuration and control subsystems are:
:SENSe{1-16}:AVERage Subsystem
:SENSe{1-16}:FSEGMent Subsystem
:SENSe{1-16}:SPUR Subsystem
:SENSe{1-16}:SWEep Subsystem
Frequency Limits
The frequency limits for the :SENSe{1-16}:FREQuency subsystem and other commands are described in detail in General Information, Minimum/Maximum Instrument Frequency and Related Parameters and the related tables in that section. In general, the frequency default values and limits are affected by two factors:
Instrument Model Number
Installed Options (Option 70)
:SENSe{1-16}:FREQuency:CENTer <NRf>
:SENSe{1-16}:FREQuency:CENTer?
Description
Sets the center value of the sweep range of the indicated channel.
Returns the center value of the sweep range of the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Hertz.
Query Parameters
<NR3> The output parameter is in Hertz.
Range
See Minimum/Maximum Instrument Frequency and Related Parameters.
Default Value
See Minimum/Maximum Instrument Frequency and Related Parameters.
Syntax Example
:SENS1:FREQ:CENT 10.0E9
:SENS1:FREQ:CENT?
:SENSe{1-16}:FREQuency:CW <NRf>
:SENSe{1-16}:FREQuency:CW?
Description
Sets the CW frequency of the indicated channel.
Returns the CW frequency of the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Hertz.
Query Parameters
<NR3> The output parameter is in Hertz.
Range
See Minimum/Maximum Instrument Frequency and Related Parameters
Default Value
See Minimum/Maximum Instrument Frequency and Related Parameters.
Syntax Example
:SENS1:FREQ:CW 10.0E9
:SENS1:FREQ:CW?
:SENSe{1-16}:FREQuency:DATA <block>
:SENSe{1-16}:FREQuency:DATA?
Description
Enters a new frequency list for the indicated channel.
Returns the frequency list for the indicated channel.
Cmd Parameters
See definition of <block> or <arbitrary block>. Frequency unit is Hertz.
Query Parameters
See definition of <block> or <arbitrary block>. Frequency unit is Hertz.
Range
NA
Default Value
NA
Syntax Example
:SENS1:FREQ:DATA <block>
:SENS1:FREQ:DATA?
:SENSe{1-16}:FREQuency:INDexed:DISCrete <block>
Description
Enters a new frequency list for the indicated channel and sets the sweep type to indexed based segmented sweep.
This command allows the entry of a single frequency list (up to 25000 or 100000 points) that can be in any order. The values must be comma-delimited in the ASCII entry format.
No query.
Cmd Parameters
See definition of <block> or <arbitrary block>.
Query Parameters
See definition of <block> or <arbitrary block>.
Range
NA
Default Value
NA
Syntax Example
:SENS1:FREQ:IND:DISC <block>
Example Entry:
:SENS:FREQ:IND:DISC #0 3.0GHz,3.0GHz,5.0GHz
:SENSe{1-16}:FREQuency:SPAN <NRf>
:SENSe{1-16}:FREQuency:SPAN?
Description
Sets the span value of the sweep range of the indicated channel.
Returns the span value of the sweep range of the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Hertz.
Query Parameters
<NR3> The output parameter is in Hertz.
Range
See Minimum/Maximum Instrument Frequency and Related Parameters
Default Value
See Minimum/Maximum Instrument Frequency and Related Parameters.
Syntax Example
:SENS1:FREQ:SPAN 5.0E9
:SENS1:FREQ:SPAN?
:SENSe{1-16}:FREQuency:STARt <NRf>
:SENSe{1-16}:FREQuency:STARt?
Description
Sets the start value of the sweep range of the indicated channel.
Returns the start value of the sweep range of the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Hertz, Meters, or Seconds.
Query Parameters
<NR3> The output parameter is in Hertz.
Range
See Minimum/Maximum Instrument Frequency and Related Parameters
Default Value
See Minimum/Maximum Instrument Frequency and Related Parameters.
Syntax Example
:SENS1:FREQ:STAR 2.0E9
:SENS1:FREQ:STAR?
:SENSe{1-16}:FREQuency:STOP <NRf>
:SENSe{1-16}:FREQuency:STOP?
Description
Sets the stop value of the sweep range of the indicated channel.
Returns the stop value of the sweep range of the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Hertz.
Query Parameters
<NR3> The output parameter is in Hertz, Meters, or Seconds.
Range
See Minimum/Maximum Instrument Frequency and Related Parameters.
Default Value
See Minimum/Maximum Instrument Frequency and Related Parameters.
Syntax Example
:SENS1:FREQ:STOP 20.0E9
:SENS1:FREQ:STOP?