VectorStar™ MS464xB Series Microwave Vector Network Analyzer Programming Manual : SCPI Commands : :SENSe{1-16}:CORRection:COLLect:MTRL:CALB Subsystem – 4-Port VNAs
 
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB Subsystem – 4-Port VNAs
The :SENSe{1-16}:CORRection:COLLect:MTRL:CALB subsystem commands control setup and data collection for the multiline TRL calibration. While similar to the LRL/LRM family, this calibration family can use multiple lines (and a match standard) at every frequency point in a weighted fashion.
These subsystems are used during various phases of calibration configuration setup:
• :CALCulate{1-16}:IMPedance:TRANsformation Subsystem
• :CALCulate{1-16}:REFerence Subsystem
• :SENSe{1-16}:CORRection:COLLect:METHod Subsystem
• :SENSe{1-16}:CORRection:COLLect:MICrostrip Subsystem
• :SENSe{1-16}:CORRection:COLLect:MULTiple Subsystem
• :SENSe{1-16}:CORRection:COLLect:MTRL[:CALa] Subsystem
• :SENSe{1-16}:CORRection:COLLect:MTRL:CALB Subsystem – 4-Port VNAs
• :SENSe{1-16}:CORRection:COLLect:TRL[:CALa] Subsystem
• :SENSe{1-16}:CORRection:COLLect:TRL:CALB Subsystem
• :SENSe{1-16}:CORRection:COLLect:TRL:SINGleton Subsystem – 4-Port VNAs
• :SENSe{1-16}:CORRection:COLLect:TRL:WAVeguide Subsystem
• :SENSe{1-16}:CORRection:COLLect Subsystem
• :SENSe{1-16}:CORRection:COLLect:WAVeguide Subsystem
• :SENSe{1-16}:CORRection:COLLect[:CALa]:PORT Subsystem
• :SENSe{1-16}:CORRection:INTerpolation Subsystem
• :SENSe{1-16}:CORRection:STATe Subsystem
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:CKIT:LOAD <string>
Description
This command requires a 4-port VNA instrument.
Loads an mTRL cal kit file into CALB mTRL calibration on the indicated channel.
No query.
Cmd Parameters
<string> Filename and path to the file in the form: x:\directory\filename.mlcf, where x:\directory\filename.mlcf exists and filename.mlcf is a valid mTRL cal kit file.
Query Parameters
NA
Query Output
NA
Range
NA
Default Value
NA
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:CKIT:LOAD 'c:\filename.mlcf'
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:CKIT:NAME <string>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:CKIT:NAME?
Description
This command requires a 4-port VNA instrument.
Sets the name that will be stored in the CALB mTRL cal kit file on the indicated channel.
Returns the name that was last set for the currently loaded CALB mTRL cal kit file on the indicated channel.
Cmd Parameters
<string> Filename and path to the file in the form: x:\directory\filename.mlcf, where x:\directory\filename.mlcf exists and filename.mlcf is a valid mTRL cal kit file.
Query Parameters
NA
Query Output
<string> The name that is currently associated with the current cal kit file.
Range
NA
Default Value
NA
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:CKIT:NAME 'c:\filename.mlcf'
:SENS1:CORR:COLL:MTRL:CALB:CKIT:NAME?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:CKIT:SAVE <string>
Description
This command requires a 4-port VNA instrument.
Saves a mTRL cal kit file into CALB mTRL calibration on the indicated channel.
No query.
Cmd Parameters
<string> Filename and path to the file in the form: x:\directory\filename.mlcf
Query Parameters
NA
Query Output
NA
Range
NA
Default Value
NA
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:CKIT:SAVE 'c:\filename.mlcf'
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:COUNt <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:COUNt?
Description
This command requires a 4-port VNA instrument.
Sets the number of lines to use in the mTRL CALB calibration on the indicated channel.
Returns the number of lines to use in the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is an integer.
Query Parameters
NA
Query Output
<NR1> The output is an integer.
Range
1 to 10
Default Value
2
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:COUN 5
:SENS1:CORR:COLL:MTRL:CALB:COUN?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:LINE{1-10}:DELay <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:LINE{1-10}:DELay?
Description
This command requires a 4-port VNA instrument.
Sets the line delay on the indicated line of the mTRL CALB calibration on the indicated channel.
Returns the line delay on the indicated line of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Seconds.
Query Parameters
NA
Query Output
<NR3> The output is in Seconds.
Range
MPND
Default Value
Default value is dependent on the default dielectric of the substrate and the effective length default value.
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:DEL 20E-3
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:DEL?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:LINE{1-10}:FREQuency <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:LINE{1-10}:FREQuency?
Description
This command requires a 4-port VNA instrument.
Sets the reference frequency on the indicated line of the mTRL CALB calibration on the indicated channel.
Returns the reference frequency on the indicated line of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Hertz.
Query Parameters
NA
Query Output
<NR3> The output is in Hertz.
Range
7E4 to 7E10
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:LINE1:FREQ 1.0E7
:SENS1:CORR:COLL:MTRL:CALB:LINE1:FREQ?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:LINE{1-10}:LENGth <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:LINE{1-10}:LENGth?
Description
This command requires a 4-port VNA instrument.
Sets the line length on the indicated line of the mTRL CALB calibration on the indicated channel.
Returns the line length on the indicated line of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Meters.
Query Parameters
NA
Query Output
<NR3> The output is in Meters.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:LINE1:LENG 1.0E0
:SENS1:CORR:COLL:MTRL:CALB:LINE1:LENG?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:LINE{1-10}:LOSS <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:LINE{1-10}:LOSS?
Description
This command requires a 4-port VNA instrument.
Sets the line loss on the indicated line of the mTRL CALB calibration on the indicated channel.
Returns the line loss on the indicated line of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in dB/mm.
Query Parameters
NA
Query Output
<NR3> The output is in dB/mm.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:LINE1:LOSS 1.0E0
:SENS1:CORR:COLL:MTRL:CALB:LINE1:LOSS?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:LINE{1-10}:MEASure
Description
This command requires a 4-port VNA instrument.
Initiates collection of the Line Standard data for the indicated line for the mTRL CALB calibration on the indicated channel.
No query.
Cmd Parameters
NA
Query Parameters
NA
Query Output
NA
Range
NA
Default Value
NA
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:LINE1:MEAS
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:LINE{1-10}:PLENgth <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:LINE{1-10}:PLENgth?
Description
This command requires a 4-port VNA instrument.
Sets the physical line length on the indicated line of the mTRL CALB calibration on the indicated channel.
Returns the physical line length on the indicated line of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Seconds.
Query Parameters
NA
Query Output
<NR3> The output is in Seconds.
Range
MPND
Default Value
Default value is dependent on effective length default value.
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:PLEN 20E-3
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:PLEN?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:MATCH[:STATe] <char>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:MATCH[:STATe]?
Description
This command requires a 4-port VNA instrument.
Sets the state of whether to include match in the mTRL CALB calibration on the indicated channel.
When enabled, the match standard will be used whenever a line length delta falls below the phase threshold specified in the match definition section.
Returns whether match will be included in the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<char> 1 | 0 | ON | OFF
Query Parameters
NA
Query Output
<char> 1 | 0
Range
NA
Default Value
0
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:MATCH 1
:SENS1:CORR:COLL:MTRL:CALB:MATCH?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:OPEN:OFFSet <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:OPEN:OFFSet?
Description
This command requires a 4-port VNA instrument.
Sets the electrical offset length of the open-like reflection of the mTRL CALB calibration on the indicated channel.
Returns the electrical offset length of the open-like reflection of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Meters.
Query Parameters
NA
Query Output
<NR3> The output is in Meters.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:OPEN:OFFS 1.0E0
:SENS1:CORR:COLL:MTRL:CALB:OPEN:OFFS?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:OPTLength[:STATe] <char>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:OPTLength[:STATe]?
Description
This command requires a 4-port VNA instrument.
Sets the state of whether to use the Optimal Length Super-Weighting in the mTRL CALB calibration on the indicated channel.
When enabled, the weighting of the various line measurements will change in computing the calibration error coefficients. The line pair with the optimal length delta for the given frequency point will be weighted more heavily and unweighting due to repeatability differences will be reduced.
Returns whether Optimal Length Super-Weighting will be used in the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<char> 1 | 0 | ON | OFF
Query Parameters
NA
Query Output
<char> 1 | 0
Range
NA
Default Value
0
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:OPTL 1
:SENS1:CORR:COLL:MTRL:CALB:OPTL?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PASSivity:ENForce[:STATe] <char>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PASSivity:ENForce[:STATe]?
Description
Sets the state of whether to use the enforced passivity in the mTRL CALB calibration on the indicated channel.
Returns whether enforced passivity will be used in the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<char> 1 | 0 | ON | OFF
Query Parameters
NA
Query Output
<char> 1 | 0
Range
NA
Default Value
0
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PASS:ENF 1
:SENS1:CORR:COLL:MTRL:CALB:PASS:ENF?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:C0 <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:C0?
Description
This command requires a 4-port VNA instrument.
Sets capacitance of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Returns capacitance of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Farads.
Query Parameters
NA
Query Output
<NR3> The output is in Farads.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:
:SENS1:CORR:COLL:MTRL:CALB:?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:C1 <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:C1?
Description
This command requires a 4-port VNA instrument.
Sets C1 coefficient of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Returns the C1 coefficient of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Farads/Hertz.
Query Parameters
NA
Query Output
<NR3> The output is in Farads/Hertz.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:C1 2.0E0
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:C1?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:C2 <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:C2?
Description
This command requires a 4-port VNA instrument.
Sets C2 coefficient of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Returns the C2 coefficient of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Farads/Hertz^2.
Query Parameters
NA
Query Output
<NR3> The output is in Farads/Hertz^2.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:C2 2.0E0
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:C2?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:C3 <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:C3?
Description
This command requires a 4-port VNA instrument.
Sets C3 coefficient of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Returns the C3 coefficient of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Farads/Hertz^3.
Query Parameters
NA
Query Output
<NR3> The output is in Farads/Hertz^3.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:C3 2.0E0
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:C3?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:L0 <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:L0?
Description
This command requires a 4-port VNA instrument.
Sets inductance of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Returns inductance of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Henrys.
Query Parameters
NA
Query Output
<NR3> The output is in Henrys.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:L0 2.01E-6
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:L0?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:L1 <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:L1?
Description
This command requires a 4-port VNA instrument.
Sets L1 coefficient of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Returns L1 coefficient of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Henrys/Hertz.
Query Parameters
NA
Query Output
<NR3> The output is in Henrys/Hertz.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:L1 2.01E0
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:L1?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:L2 <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:L2?
Description
This command requires a 4-port VNA instrument.
Sets L2 coefficient of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Returns L2 coefficient of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Henrys/Hertz^2.
Query Parameters
NA
Query Output
<NR3> The output is in Henrys/Hertz^2.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:L2 2.01E0
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:L2?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:L3 <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:L3?
Description
This command requires a 4-port VNA instrument.
Sets L3 coefficient of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Returns L3 coefficient of match on the indicated port of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Henrys/Hertz^3.
Query Parameters
NA
Query Output
<NR3> The output is in Henrys/Hertz^3.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:L3 2.01E0
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:L3?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:MEASure
Description
This command requires a 4-port VNA instrument.
Initiates collection of match standard data for the mTRL CALB calibration on the indicated channel and port.
No query.
Cmd Parameters
NA
Query Parameters
NA
Query Output
NA
Range
NA
Default Value
NA
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:MEAS
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:OFFS <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:OFFS?
Description
This command requires a 4-port VNA instrument.
Sets the offset length of match of the mTRL CALB calibration on the indicated channel.
Returns the offset length of match of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Meters.
Query Parameters
NA
Query Output
<NR3> The output is in Meters.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:OFFS 1.0E0
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:OFFS?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:OFF1 <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:OFF1?
Description
This command requires a 4-port VNA instrument.
Sets the offset length1 coefficient of match of the mTRL CALB calibration on the indicated channel.
Returns the offset length1 coefficient of match of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Meters/Hertz.
Query Parameters
NA
Query Output
<NR3> The output is in Meters/Hertz.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:OFF1 2.0E0
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:OFF1?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:OFF2 <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:OFF2?
Description
This command requires a 4-port VNA instrument.
Sets the offset length2 coefficient of match of the mTRL CALB calibration on the indicated channel.
Returns the offset length2 coefficient of match of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Meters/Hertz^2.
Query Parameters
NA
Query Output
<NR3> The output is in Meters/Hertz^2.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:OFF2 2.0E0
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:OFF2?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:OFF3 <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:OFF3?
Description
This command requires a 4-port VNA instrument.
Sets the offset length3 coefficient of match of the mTRL CALB calibration on the indicated channel.
Returns the offset length3 coefficient of match of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Meters/Hertz^3.
Query Parameters
NA
Query Output
<NR3> The output is in Meters/Hertz^3.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:OFF3 2.0E0
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:OFF3?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:R <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:R?
Description
This command requires a 4-port VNA instrument.
Sets the resistance of match of the mTRL CALB calibration on the indicated channel.
Returns the resistance of match of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Ohms.
Query Parameters
NA
Query Output
<NR3> The output is in Ohms.
Range
MPND
Default Value
5.00000000000E+001
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:R 7.5E1
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:R?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:S1P:FILE <string>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:S1P:FILE?
Description
This command requires a 4-port VNA instrument.
Sets the match s1p file on the indicated port of the mTRL CALB calibration on the indicated channel.
Returns the match s1p file on the indicated port of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<string> Filename and path to the file in the form: x:\directory\filename.s1p, where x:\directory\filename.s1p must exist.
Query Parameters
NA
Query Output
<string> Filename and path in the form: x:\directory\filename.s1p.
Range
NA
Default Value
NA
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:FILE 'c:\filename.s1p'
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:FILE?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:S1P[:STATe] <char>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:S1P[:STATe]?
Description
This command requires a 4-port VNA instrument.
Sets the MATCH S1P file settings ON/OFF on the selected port for mTRL CALB calibration for the indicated channel. ON means that the S1P file data will be used, OFF means the Circuit Model data will be used.
Returns the MATCH S1P file settings on the selected port for mTRL CALB calibration for the indicated channel.
Cmd Parameters
<char> 1 | 0 | ON | OFF
Query Parameters
NA
Query Output
<char> 1 | 0
Range
NA
Default Value
0
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:S1P 1
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:S1P?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:THReshold <double>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:THReshold?
Description
This command requires a 4-port VNA instrument.
Sets the electrical line length delta for match use for CALB calibration on the indicated channel.
Returns the electrical line length delta for match use for CALB calibration on the indicated channel.
Cmd Parameters
<double> The input is in degrees.
Query Parameters
NA
Query Output
<string> The output is in degrees.
Range
[0-180]
Default Value
20.0
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:THR 50
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:THR?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:Z0 <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:PORT{1-4}:MATCH:Z0?
Description
This command requires a 4-port VNA instrument.
Sets the impedance of match of the mTRL CALB calibration on the indicated channel.
Returns the impedance of match of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in Ohms.
Query Parameters
NA
Query Output
<NR3> The output is in Ohms.
Range
MPND
Default Value
5.00000000000E+001
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:Z0 7.5E1
:SENS1:CORR:COLL:MTRL:CALB:PORT1:MATCH:Z0?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:REFLection:TYPE <char>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:REFLection:TYPE?
Description
This command requires a 4-port VNA instrument.
Sets the reflection type of the mTRL CALB calibration on the indicated channel, where:
• OPENlike = The reflection type is more like an open.
• SHORTlike = The reflection type is more like a short.
Returns the reflection type of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<char> OPENlike | SHORTlike
Query Parameters
NA
Query Output
<char> OPEN | SHORT
Range
NA
Default Value
SHORT
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:REFL:TYPE OPEN
:SENS1:CORR:COLL:MTRL:CALB:REFL:TYPE?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:REFPlane <char>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:REFPlane?
Description
This command requires a 4-port VNA instrument.
Sets the location of the reference plane in the mTRL CALB calibration on the indicated channel where:
• MIDdle = the middle of the transmission line
• END = the end of the transmission line
Returns the location of the reference plane in the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<char> MIDdle | END
Query Parameters
NA
Query Output
<char> MID | END
Range
NA
Default Value
END
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:REFP MID
:SENS1:CORR:COLL:MTRL:CALB:REFP?
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:SHORT:OFFSet <NRf>
:SENSe{1-16}:CORRection:COLLect:MTRL:CALB:SHORT:OFFSet?
Description
This command requires a 4-port VNA instrument.
Sets the offset length of the short-like reflection of the mTRL CALB calibration on the indicated channel.
Returns the offset length of the short-like reflection of the mTRL CALB calibration on the indicated channel.
Cmd Parameters
<NRf> The input parameter is in meters.
Query Parameters
NA
Query Output
<NR3> The output is in meters.
Range
MPND
Default Value
0.00000000000E+000
Syntax Example
:SENS1:CORR:COLL:MTRL:CALB:SHORT:OFFS 1.0E0
:SENS1:CORR:COLL:MTRL:CALB:SHORT:OFFS?