VectorStar™ MS464xB Series Microwave Vector Network Analyzer User Interface Reference : 0Power Menus – 4-Port VNAs : Power Menu Sets
 
Power Menu Sets
Power Menus for Frequency-Based Sweep – 4-Port VNAs
The power menu set for frequency-based sweep is shown in the figure below.
Power Menu Set – Frequency-Based Sweep (Linear or Log) (1 of 2)
This power menu set, including menu appearance and menu links, is available if Sweep Type is set to Frequency-Based (Linear) or Frequency-Based (Log), When Modular BB is enabled on the APPLICATION menu on MS4647B only when equipped with Options 007, 070, and 08x, some power menus have either relabeled buttons or additional buttons. The button changes are related to power levels above and below 54 GHz.
3. POWER SETUP Menu – Frequency-Based Sweep – 4-Port VNAs. Leveling Mode is visible only if the application is set to PulseView. Refresh Leveling Reference is only visible in Per Sweep Pulsed and Per Point Pulsed leveling modes.
9. mmWAVE ALC CAL Menu. The mmWave CAL button is visible only in 3739 or Multiple Source modes when mmWave control is enabled.
 
Power Menus for Frequency-Based Sweep – 4-Port VNAs (Option 32)
The power menu set for frequency-based sweep with Option 32 installed is shown in the figure below.
Power Menu Set – Frequency-Based Sweep with Option 32 (1 of 2)
With Option 32 installed, the Source 2 power can be redirected out of Port 1 or Port 2.
When SRC2 Out Redirection is ON, all other menus remain the same except for those that are shown above.
When SRC2 Out Redirection is OFF, Port selection reverts to a toggle between a choice of Port 1, Port 2, Port 3, or Port 4.
2. POWER SETUP Menu – Frequency-Based Sweep – 4-Port VNAs with Option 32. Leveling Mode is visible only if the application is set to PulseView. Refresh Leveling Reference is only visible in Per Sweep Pulsed and Per Point Pulsed leveling modes.
4. SELECT PORT Dialog Box
Power Menus for Segment-Based Sweep – 4-Port VNAs
The POWER menu set for segment-based sweep is shown in the figure below.
Power Menu Set – Segmented Sweeps (Frequency or Index-Based) (1 of 2)
This POWER menu set is available if Sweep Type is set to Segmented Sweep (Frequency-Based) or Segmented Sweep (Index-Based). When Modular BB is enabled on the APPLICATION menu, some power menus have relabeled buttons and/or additional buttons. The power settings for segmented sweeps (frequency-based or index-based) are in the segmented-sweep input tables.
5. POWER SETUP Menu – Segment-Based Sweep – 4-Port VNAs. Leveling Mode is visible only if the application is set to PulseView. Refresh Leveling Reference is only visible in Per Sweep Pulsed and Per Point Pulsed leveling modes.
9. mmWAVE ALC CAL Menu. The mmWave CAL button is visible only in 3739 or Multiple Source modes when mmWave control is enabled.
Power Menus for Power-Based Sweep – 4-Port VNAs
The power menu set for power-based sweep is shown in the Figure: Power Menu Set – Power-Based Sweep (CW or Swept Frequency) (1 of 2).
Power Menu Set – Power-Based Sweep (CW or Swept Frequency) (1 of 2)
This power menu set is available if Sweep Type is set to Power Sweep (CW Freq) or Power Sweep (Swept Freq). When Modular BB is enabled on the APPLICATION menu, some power menus have relabeled buttons and/or additional buttons.
2. POWER SETUP Menu – Power-Based Sweep Menu – 4-Port VNAs. Leveling Mode is visible only if the application is set to PulseView. Refresh Leveling Reference is only visible in Per Sweep Pulsed and Per Point Pulsed leveling modes.
9. mmWAVE ALC CAL Menu. The mmWave CAL button is visible only in 3739 or Multiple Source modes when mmWave control is enabled.
Power Menus for Power-Based Sweep – 4-Port VNAs (Option 32)
The power menu set for power-based sweep with Option 32 installed is shown in the figure below.
Power Menu Set – Power-Based Sweep with Option 32 (1 of 2)
With Option 32 installed, the Source 2 power can be redirected out of Port 1 or Port 2.
When SRC2 Out Redirection is ON, all other menus remain the same except for those that are shown above.
When SRC2 Out Redirection is OFF, Port selection reverts to a toggle between a choice of Port 1, Port 2, Port 3, or Port 4.
2. POWER SETUP Menu – Power-Based Sweep Menu – 4-Port VNAs with Option 32. Leveling Mode is visible only if the application is set to PulseView. Refresh Leveling Reference is only visible in Per Sweep Pulsed and Per Point Pulsed leveling modes.
4. SELECT PORT Dialog Box