VNA Master™Programming Manual : VNA Commands
 
VNA Commands
 
Introduction
VNA Commands
:CALCulate Subsystem
Trace Data Transfer
:CALCulate:FORMat Subsystem
Graph Type
:CALCulate:LIMit Subsystem
Limit Alarm
Number of Lower Limit Points
Add Lower Limit Point
Delete Lower Limit Point
Lower Limit Next Point Left
Lower Limit Next Point Right
Lower Limit Point X Value
Lower Limit Point Y Value
Lower Limit State
Lower Limit X Value
Lower Limit Y Value
Number of Limit Points
Add Limit Point
Delete Limit Point
Next Point Left
Next Point Right
Limit Point X Value
Limit Point Y Value
Limit State
Limit Type
Number of Upper Limit Points
Add Upper Limit Point
Delete Upper Limit Point
Upper Limit Next Point Left
Upper Limit Next Point Right
Upper Limit Point X Value
Upper Limit Point Y Value
Upper Limit State
Upper Limit X Value
Upper Limit Y Value
Limit X Value
Limit Y Value
:CALCulate:MARKer Subsystem
Turn All Markers Off
Marker Data
Delta Marker Reference To
Delta Marker State
Marker Readout Format
Marker Domain Type
Marker Readout Style
Marker (Maximum) Peak Search
Marker (Minimum) Valley Search
Reference Marker State
Marker On Trace
Marker Type
Marker X Value
Marker Read Y Value
:CALCulate:MATH Subsystem
Trace To Memory
:CALCulate:SMOothing Subsystem
Smoothing
:CALCulate:TRANsform Subsystem
Maximum Distance
Distance Resolution
Start Distance
Stop Distance
Distance Units
Get Distance List
:Display Subsystem
Trace Display
Trace Format
Group Delay Aperture
Scale Resolution Per Division
Scale Reference Level
Scale Reference Line
Smith Chart Scalable Type
:Format Subsystem
Numeric Data Format
:INITiate Subsystem
Continuous/Single Sweep
Hold Sweep
Trigger Sweep/Measurement
:INPut Subsystem
Internal Bias Tee Current
Internal Bias Tee Tripped State
Bias Tee State
Internal Bias Tee Voltage
:MMEMory Subsystem
:MMEMory:LOAD Subsystem
Recall Setup
Recall Measurement
:MMEMory:STORe Subsystem
Save Setup
Save Measurement
[:SENSe] Subsystem
RF Power In Hold State
[:SENSe]:APPLication Subsystem
Application Self Test
Application Self Test Result
[:SENSe]:AVERage Subsystem
Restart Averaging
Number of Traces to Average
[:SENSe]:CALibration Subsystem
Calibration State
[:SENSe]:CORRection Subsystem
Error Correction Data
Smith Chart Reference Impedance
Calibration Correction State
[:SENSe]:CORRection:CKIT Subsystem
Calibration Connector Information
[:SENSe]:CORRection:CKIT:USER Subsystem
DUT User Inductance Coefficient value
DUT User Capacitance Coefficient value
DUT User Name
DUT User Open Offset
DUT User Short Offset for calibration method SOLT
[:SENSe]:CORRection:COLLect Subsystem
Calibration Abort
Calibration Steps
Calibration Steps and Calibration Types:
Calibration Step Status
DUT Port Setup
Calibration Interpolation
Calibration Line Type
Calibration Method
Calculate Calibration Data
Calibration Status
Calibration Accuracy Status
Calibration Type
[:SENSe]:FREQuency Subsystem
Center Frequency
Frequency Span
Distance Suggested Frequency Span
Start Frequency
Stop Frequency
Get Frequency List
[:SENSe]:SWEep Subsystem
IF Bandwidth
Number of Sweep Points
Sweep Type
[:SENSe]:TRACe Subsystem
Trace Domain
Trace Select
S Parameter
Number of Traces
Active Trace
:SOURce Subsystem
Power Levels
:SOURce:CORRection:RVELocity Subsystem
Propagation Velocity
Cable Loss
:STATus Subsystem
Query Operation Status
:SYSTem Subsystem
System Alternate State
Motherboard Temperature
Preset
:Trace Subsystem
Trace Data Transfer
Trace Header Transfer
Introduction
This chapter describes commands for Vector Network Analyzer mode. Only the commands that are listed in this chapter and in All Mode Commands can be used in Vector Network Analyzer mode. Using commands from other modes may produce unexpected results.
Note 
Front Panel Access in VNA mode via the function hard keys may be listed as Freq/Dist or as Freq. The first function hard key is displayed with the label Freq/Dist when Option 501 is installed in the VNA Master.
Notational conventions are described in Command and Query Notational Conventions.
VNA Commands
VNA Commands Subsystems
Keyword
Parameter Data or Units
:CALCulate{1-4}
:DISPlay
:FORMat
:INITiate
:INPut
:MMEMory
[:SENSe]
:SOURce
:STATus
:SYSTem
:TRACe