Rubidium™ RF/Microwave Signal Generator
Important Notices and Warranty
Applicable Product Models
Unauthorized Use or Disclosure
Export Management
Trademark Acknowledgments
Warranty Information
Limitation of Warranty
Disclaimer of Warranties
No Liability For Consequential Damages
Safety
Safety Notices Used in Manuals
Safety Symbols Used on Equipment and in Manuals
Safety Symbols and Notices
Regulatory Compliance
Compliance Notifications
CE Conformity Marking
European Parliament and Council Directive 2012/19/EC
RCM Conformity Marking
KCC Conformity Marking
Canadian ICES-001 and ICES-003 Conformity Marking
Recycle Marking
Proposition 65 Notification
Perchlorate Material Notification – Special Handling May Apply
Chinese RoHS Compliance Statement
General Information
About this Guide
About this Chapter
Additional Documentation
Options
Description
Instrument Integrity
Antivirus Protection
ESD Caution
Instrument Care and Preventive Maintenance
Cleaning the Fan Grill
Connector Care
Power Output
Unpacking the Product
Operating Environment
Typographic Conventions
Preparation for Storage/Shipment
Preparation for Storage
Preparation for Shipment
Contacting Anritsu for Sales and Service
Instrument Identification
Instrument Overview
Introduction
Front Panel
Front Panel Controls
Menu Buttons
Rotary Knob
Cursor Control Pad
Numeric Keypad
RF Output
Rear Panel
Rear Panel BNCs
Installation and Power Requirements
Powering On the MG362x1A
Standby Mode
Warm-up Time
Common GUI Controls
GUI Overview
Title Bar
Menu Buttons
Status Area
Entering Data
Opening a Parameter
Cursor Control Buttons
Text Entry
System Menu
SYSTEM INFORMATION
INSTRUMENT Menu
SOFTWARE Menu
CONNECTIVITY Menu
SETTINGS Menu
DISPLAY Settings
SOUND Settings
ETHERNET Settings
Network Settings
Connecting to the MG362x1A or Localhost
Working with the Localhost
Measurement Setup Parameters
REMOTE Settings
GPIB Interface Connection and Setup
SCREENSHOT Settings
Previewing Screenshots
DATE TIME Settings
OPTIONS Menu
RESET Menu
Resetting to Default Parameters
FILES Menu
File Management
File Locations
File Management Operations
DIAGNOSTICS Menu
EVENT LOG Menu
SELF TEST
SERVICE Mode
TOOLS
Instrument Operation
Introduction
Power-on Display
Standby Mode
Self Testing the MG362x1A
Resetting to Default Parameters
CW Frequency Operation
FREQUENCY Menu
Phase Offset Menu
FREQUENCY PRESETS Menu
Frequency Sweep Operation
SWEEP Menu
Analog Sweep (Option 6)
Editing the Current Start/Stop Frequencies
Setting PRESET SWEEP RANGES
Setting Sweep Time
Trigger Menu
RANGE Menu
Frequency Step Sweep Operation
SWEEP Menu
SUMMARY Menu
Step Sweep SETUP Menu
Editing the Current Start/Stop Frequencies
Setting the Step Size
Number of Points
Setting DWELL TIME
Setting SWEEP DIRECTION
Setting PRESET SWEEP RANGE
RANGE Menu
Setting SWEEP TYPE
Starting a Step Sweep
TRIGGER Menu
Sweep TRIGGER TYPES
Initiate Step Sweep
LIST Menu
SWEEP LIST Index
LIST TRIGGER Menu
LIST - LIST Menu
Copy to the LIST
Power Level Operations
LEVEL Menu
LEVEL SETUP Menu
Units
LEVEL PRESETS Menu
Setting Fixed Power
Setting a Preset Power Level.
LEVEL OFFSET Menu
Edit the Offset Value
Power Level Sweep Operation
LEVEL SWEEP Menu
Setting CW Power Sweep, Step Size, and Dwell Time
Triggering a CW Power Sweep
RANGE Menu
Setting a Power Level Sweep Range
Setting SWEEP TYPE
Setting the ALC Control
ALC Menu
ALC Level Modes
ALC Power Slope
Step Attenuator (Option 2)
ATTENUATOR Menu
Decoupling the Attenuator
POWER SEARCH Menu
Modulation
Amplitude Modulation
Setting AM SOURCE
Amplitude Modulation Set to Internal
Amplitude Modulation Set to External
Frequency Modulation
Setting FM SOURCE
Frequency Modulation Set to Internal
Frequency Modulation Set to External
Phase Modulation
PHASE Modulation Set to Internal
PHASE Modulation Set to External
Pulse Modulation
Setting Pulse SOURCE
PULSE Modulation Set to Internal
Setting Period and (PRF) FREQUENCY
Pulse Width-Delay Menu
PULSE Modulation Set to External
Phase Tracking
Saving/Recalling Instrument Setups
Saving Setups
Erasing Stored Setups
Reference CALIBRATION
100 MHz Calibration (Standard Reference)
10 MHz Calibration (Option 3)
100 MHz Calibration
100 MHz Status
10 MHz Calibration With Option 66
RUBIDIUM Menu (Option 56)
GNSS Menu (Option 66)
Reference Status Conditions
Reference Oscillator Current Source
Reference Oscillator Lock Status
Reference Oscillator 100 MHz Lock Status
Reference Oscillator GPS Lock Status
Reference Oscillator Rubidium Lock Status
Config Menu
Secure Mode
Increment Size
RESET Menu
Operation Verification
Introduction
Test Records
Initial MG362x1A Checkout
Power On
Warm-up Time
Self Test
Presetting the MG362x1A
Frequency Synthesis Test
Level Accuracy and Flatness Test
Accuracy Test Procedure
Flatness Test Procedure
Software Installation
Install MG362x1A
PC Requirements
Installation
FILE (File Management)
Updating Firmware
Introduction
Updating Firmware on the MG362x1A
Use the MG362x1A WEB UPDATES Menu
Use a USB Memory Device
Software Option Upgrades
Introduction
Upgrade Procedure
Exporting a Software Configuration File
Importing Software License
Instrument Messages
Introduction
Error Messages
Informational Messages
Warning Messages
Self-Test Messages
Rubidium™ MG362x1A SeriesLow-Noise RF/Microwave SignalGenerators
General GPIB, Ethernet Information
Introduction
Chapter Introduction
Scope of Manual
Related Manuals
Operation Manual
Maintenance Manual
Technical Data Sheet
MG362x1A GPIB
Setting GPIB Operating Parameters
Selecting the Interface Language
Response to GPIB Interface Function Messages
Remote Programming Setup and Interface
VISA (Virtual Instrument System Architecture)
Interface Connectors
GPIB Interconnection and Setup
GPIB Interconnection
GPIB Cable Length Restrictions
Setting the GPIB Address
Selecting the GPIB OUTPUT TERMINATOR
Ethernet LAN TCP/IP Requirements and Setup
TCP/IP General Requirements and Settings
NI-VISA
Communicate Over GPIB – Example
Communicate Over Sockets – Example
HiSLIP
Read and Write Example
Programming with SCPI Commands
Introduction
Introduction to SCPI Programming
SCPI Command Types
Common Commands
Required and Optional SCPI Commands
Query Commands
Command Names
Hierarchical Command Structure
Data Parameters
Unit Suffixes
Notational Conventions
General Notations
Parameter Notations
Notational Examples
SCPI Interface Language Selection
Remote Selection
Status System Programming
Status Group Registers
Status Group Reporting
Trigger System Programming
Trigger System Operation
Native Programming
Introduction
Command Codes
Data Input Restrictions
Parameter and Data Entry Commands
Data Entry
Configuration Commands
CW Frequency Commands
Output Power Leveling Commands
RF Output Power Level Selection
Attenuator Decoupling
Modulation Commands
Phase Modulation
Pulse Modulation
Modulation Command List
Output Commands
SRQ and Status Byte Commands
SRQ Generation
Primary and Extended Status Bytes
Self Test Command
Self Test Example
Miscellaneous Commands
Command Directory
Typographic Conventions
Functional Categories
Commands
*IDN?
ACW
AT0
AT1
ATT(xx)
CF0 or CF0 <value> <unit>
CF1 <value> <unit>
CLR
CSB
D1 <value> <unit>
DS0
DS1
EL0
EL1
F1 <value> <unit>
FB0
FB1
IP
L0 or L0 <value> <unit>
L1 <value> <unit>
LE0
LE1
LO0
LO1
LOS <value> <unit>
LS0
LS1
MB0
MB1
MB2
OEM
OES
OPP
OSB
OSR
P0
P3
P4
PC4
PDY <value> <unit>
PE0
PE1
PER <value> <unit>
PMD(x)
PTG(x)
PW <value> <unit>
RF0
RF1
RL
RO0
RO1
RST
SB0
SB1
SQ0
SQ1
SYST:LANG "SCPI”
TST
UL0
UL1
W1 <value> <unit>
XP
SCPI Commands
Introduction
Parameter Ranges
Common Commands
*CLS
*ESE <numeric_value>
*ESR?
*IDN?
*OPC
*OPT?
*RCL <numeric_value>
*RST
*SAV <numeric_value>
*SRE <numeric_value>
*STB?
*TRG
*TST?
*WAI
:DIAGnostic:MEMory?
:FETCh:GPS?
:FETCh:GPS:ALL?
:FETCh:GPS:FULL?
:INSTrument:APPLication:STATe <SG>,<0 | 1 | ON | OFF>
:INSTrument:CATalog:ACTive?
:INSTrument:CATalog:ALL?
:INSTrument:CATalog:FULL?
:INSTrument:NSELect <numeric_value>
:INSTrument[:SELect] <SG>
:MMEMory:CATalog:DIRectory? <string>,<string>
:MMEMory:CATalog:DIRectory:SIZE? <string>,<string>
:MMEMory:CATalog:MSUSs?
:MMEMory:CDIRectory <string>
:MMEMory:COPY <string>,<string>,<string>,<string>
:MMEMory:CREate:DIRectory <string>,<string>
:MMEMory:DATA <string>,<string>,<block data>
:MMEMory:DELete:DIRectory <string>,<string>
:MMEMory:DELete:FILe <string>,<string>
:MMEMory:EJECt <string>
:MMEMory:LOAD:STATe <numeric_value>,<string>,<string>
:MMEMory:MSIS <string>
:MMEMory:STORe:SCReen
:MMEMory:STORe:STATe <numeric_value>,<string>,<string>
:STATus:OPERation:CONDition?
:STATus:OPERation:ENABle <numeric_value>
:STATus:OPERation[:EVENt]?
:STATus:OPERation:NTRansition <numeric_value>
:STATus:OPERation:PTRansition <numeric_value>
:STATus:PRESet
:STATus:QUEStionable:CONDition?
:STATus:QUEStionable:ENABle <numeric_value>
:STATus:QUEStionable[:EVENt]?
:STATus:QUEStionable:NTRansition <numeric_value>
:STATus:QUEStionable:PTRansition <numeric_value>
:SYSTem:COMMunicate:GPIB:ADDRess:PRIMary <numeric_value>
:SYSTem:COMMunicate:GPIB:TERMinator:OUTPut <CRETurn|CRLFeed|LFEed>
:SYSTem:COMMunicate:LAN:CONFig <string>,[<string>],[<string>]
:SYSTem:COMMunicate:LAN:CONFig:CURRent?
:SYSTem:COMMunicate:LAN:DHCP <ON|OFF>
:SYSTem:COMMunicate:LAN:DNS <string>,<string>,<string>
:SYSTem:COMMunicate:LAN:DNSServer:APPend <string>, {<string>}, ...
:SYSTem:COMMunicate:LAN:DNSServer:DELete <string>, {<string>}, ...
:SYSTem:COMMunicate:LAN:DNSServer:LIST <string>, {<string>}, ...
:SYSTem:COMMunicate:LAN:FTP:STATe <0 | 1 | ON | OFF>
:SYSTem:COMMunicate:LAN:HOSTname <string>
:SYSTem:COMMunicate:LAN:HTTP:SECure:STATe <0 | 1 | ON | OFF>
:SYSTem:DATE <numeric_value>,<numeric_value>,<numeric_value>
:SYSTem:DEFault:RESet:ALL
:SYSTem:DEFault:RESet:DATA <USER|SYSTem>
:SYSTem:DEFault:RESet:FACTory
:SYSTem:ERRor:DISPlay <0 | 1 | ON | OFF>
:SYSTem:ERRor[:NEXT]?
:SYSTem:FIRMware:UPDate <string>,<string>
:SYSTem:FIRMware:UPDate:LIST?
:SYSTem:FIRMware:UPDate:REMote <string>
:SYSTem:FIRMware:UPDate:REMote:AUTO <0 | 1 | ON | OFF>
:SYSTem:FIRMware:UPDate:REMote:LATest?
:SYSTem:FIRMware:UPDate:REMote:LIST?
:SYSTem:FIRMware:UPDate:REMote:LIST:REFResh
:SYSTem:FIRMware:UPDate:REMote:SOURce <string>
:SYSTem:FIRMware:VERSion?
:SYSTem:GPS:SEARch:MODE <GGLonass|GGALileo|GBEidou|GGGalileo>
:SYSTem:GPS:STATe <0 | 1 | ON | OFF>
:SYSTem:LOG:ERRor?
:SYSTem:MACaddress?
:SYSTem:MODel:OVERride <NONE|MG369xA|MG369xB|MG369xC>
:SYSTem:OPTions?
:SYSTem:OPTions:ALL?
:SYSTem:OPTions:CONFig?
:SYSTem:OPTions:TIMed:ACTivate <string>
:SYSTem:OPTions:UPDate:REMote
:SYSTem:OPTions:UPGRade <string>
:SYSTem:PRESet
:SYSTem:REBoot
:SYSTem:SHUTdown
:SYSTem:TEMPerature?
:SYSTem:TIME <numeric_value>,<numeric_value>,<numeric_value>
:SYSTem:TIME:SYNC <AUTO|MANual>
:SYSTem:TIME:SYNC:STATus?
:SYSTem:TIME:ZONE <string>
:SYSTem:TIME:ZONE:CATalog?
:SYSTem:UNIT:NAMe <string>
:TEST:SELFtest?
:ABORt
:DIAGnostic:CALibration:AMPLitude:INTernal:ABORt
:DIAGnostic:CALibration:AMPLitude:INTernal:DATE?
:DIAGnostic:CALibration:AMPLitude:INTernal:INFO?
:DIAGnostic:CALibration:AMPLitude:INTernal:PAD:LOAD <string>,<string>
:DIAGnostic:CALibration:AMPLitude:INTernal:PAD:NAME?
:DIAGnostic:CALibration:AMPLitude:INTernal:PAD:STORe <string>,<string>
:DIAGnostic:CALibration:AMPLitude:INTernal:RANGe?
:DIAGnostic:CALibration:AMPLitude:INTernal:SENSor?
:DIAGnostic:CALibration:AMPLitude:INTernal:STARt
:DIAGnostic:CALibration:AMPLitude:INTernal:STATe <0 | 1 | ON | OFF>
:DIAGnostic:CALibration:ATTenuator:INTernal:ABORt
:DIAGnostic:CALibration:ATTenuator:INTernal:DATE?
:DIAGnostic:CALibration:ATTenuator:INTernal:INFO?
:DIAGnostic:CALibration:ATTenuator:INTernal:RANGe?
:DIAGnostic:CALibration:ATTenuator:INTernal:SENSor?
:DIAGnostic:CALibration:ATTenuator:INTernal:STARt
:DIAGnostic:CALibration:ATTenuator:INTernal:STATe <0 | 1 | ON | OFF>
:DIAGnostic:CALibration:INTernal:EXPort <string>,<string>
:DIAGnostic:CALibration:REFerence:ABORt
:DIAGnostic:CALibration:REFerence:DATE?
:DIAGnostic:CALibration:REFerence:INITiate
:DIAGnostic:CALibration:REFerence:LFRequency:ABORt
:DIAGnostic:CALibration:REFerence:LFRequency:DATE?
:DIAGnostic:CALibration:REFerence:LFRequency:INITiate
:DIAGnostic:CALibration:REFerence:LFRequency:SOURce?
:DIAGnostic:CALibration:REFerence:LFRequency:STATus?
:DIAGnostic:CALibration:REFerence:STATus?
:DIAGnostic:MODule:INFOrmation?
:DIAGnostic:SNUM?
:DISPlay[:WINDow]:TEXT:STATe <0 | 1 | ON | OFF>
:INITiate:CONTinuous <0 | 1 | ON | OFF>
:INITiate[:IMMediate]
:INITiate:SG:SELFtest?
:MEASure:AM[:EXTernal]:DEPTh?
:MEASure:FM[:EXTernal]:DEViation?
:MEASure:PM:DEViation?
:MMEMory:LOAD:CORRection<n> <string>,<string>
:MMEMory:STORe:CORRection<n> <string>,<string>
:OUTPut:IMPedance?
:OUTPut:PNAmplifier:STATe <0 | 1 | ON | OFF>
:OUTPut:PRESet[:STATe] <0 | 1 | ON | OFF>
:OUTPut:PROTection <0 | 1 | ON | OFF>
:OUTPut:PROTection:RETRace <0 | 1 | ON | OFF>
:OUTPut:ROSCillator:HFRequency[:STATe] <0 | 1 | ON | OFF>
:OUTPut:ROSCillator:MULTiplied[:STATe] <0 | 1 | ON | OFF>
:OUTPut:ROSCillator:PPSecond[:STATe] <0 | 1 | ON | OFF>
:OUTPut:ROSCillator[:STATe]?
:OUTPut[:STATe] <0 | 1 | ON | OFF>
[:SOURce]:AM:ERRor?
[:SOURce]:AM[:EXTernal]:LOGSens <numeric_value> | DEFault | MINimum | MAXimum
[:SOURce]:AM[:EXTernal]:SENSitivity <numeric_value> | DEFault | MINimum | MAXimum
[:SOURce]:AM[:INTernal]:DEPTh <percent_value> | DEFault | MINimum | MAXimum
[:SOURce]:AM[:INTernal]:FREQuency <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:AM[:INTernal]:LOGDepth <numeric_value> {DB} | DEFault | MINimum | MAXimum
[:SOURce]:AM[:INTernal]:WAVE <SINE|GAUSsian|RDOWn|RUP|SQUare|TRIangle|UNIForm>
[:SOURce]:AM:SOURce <INTernal|EXTernal>
[:SOURce]:AM:STATe <0 | 1 | ON | OFF>
[:SOURce]:AM:TYPE <LINear|LOGarithmic>
[:SOURce]:CORRection<n>:PMETer:OFFSet <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:CORRection<n>:PMETer:SCALe <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:CORRection<n>:POINts <numeric_value> | DEFault | MINimum | MAXimum
[:SOURce]:CORRection<n>:STARt <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:CORRection<n>:STEP <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:CORRection<n>:STOP <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:CORRection:CALibrate:ABORt
[:SOURce]:CORRection:CALibrate:STARt
[:SOURce]:CORRection:CALibrate:STATus?
[:SOURce]:CORRection:CSET:SELect <NONE|USER{1}|USER{2}|USER{3}|USER{4}|USER{5}>
[:SOURce]:CORRection:DEVice <USB|ML2437|ML2438>
[:SOURce]:CORRection[:STATe] <0 | 1 | ON | OFF>
[:SOURce]:FM:ERRor?
[:SOURce]:FM[:EXTernal]:METer:INTerval <numeric_value> {PS | NS | US | MS | S | MIN | HR} | DEFault | MINimum | MAXimum
[:SOURce]:FM[:EXTernal]:SENSitivity <numeric_value> {HZ/V | KHZ/V | MHZ/V | GHZ/V} | DEFault | MINimum | MAXimum
[:SOURce]:FM:HFILter <DC|HP63|HP1K>
[:SOURce]:FM[:INTernal]:DEViation <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:FM[:INTernal]:FREQuency <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:FM[:INTernal]:WAVE <SINE|GAUSsian|RDOWn|RUP|SQUare|TRIangle|UNIForm>
[:SOURce]:FM:MODE <LOCKed{[1]|2}|UNLocked>
[:SOURce]:FM:SOURce <INTernal|EXTernal>
[:SOURce]:FM:STATe <0 | 1 | ON | OFF>
[:SOURce]:FREQuency:CENTer <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:FREQuency[:CW|FIXed] <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum | UP | DOWN
[:SOURce]:FREQuency[:CW|FIXed]:STEP[:INCRement] <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:FREQuency[:CW]:SELect <F0|F1|F2|F3|F4|F5|F6|F7|F8|F9>
[:SOURce]:FREQuency:DELTa <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:FREQuency:F<n> <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:FREQuency:MODE <CW|FIXed|SWEep{[1]}|LIST{[1]}|LIST{2}|LIST{3}|LIST{4}|LIST{5}|LIST{6}|LIST{7}|LIST{8}|LIST{9}|LIST{10}>
[:SOURce]:FREQuency:SPAN <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:FREQuency:SPAN:FULL
[:SOURce]:FREQuency:STARt <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:FREQuency:STOP <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:LIST<n>:FREQuency <numeric_value> {HZ | KHZ | MHZ | GHZ}, {<numeric_value> {HZ | KHZ | MHZ | GHZ}}, ...
[:SOURce]:LIST<n>:FREQuency:UPDate <numeric_value>,<numeric_value> {HZ | KHZ | MHZ | GHZ}, {<numeric_value> {HZ | KHZ | MHZ | GHZ}}, ...
[:SOURce]:LIST<n>:INDex <numeric_value> | DEFault | MINimum | MAXimum
[:SOURce]:LIST<n>:POWer <numeric_value> {<amplitude_units>}, {<numeric_value> {<amplitude_units>}}, ...
[:SOURce]:LIST<n>:POWer:UPDate <numeric_value>,<numeric_value> {<amplitude_units>}, {<numeric_value> {<amplitude_units>}}, ...
[:SOURce]:LIST<n>:PRESet
[:SOURce]:LIST<n>:STARt <numeric_value> | DEFault | MINimum | MAXimum
[:SOURce]:LIST<n>:STOP <numeric_value> | DEFault | MINimum | MAXimum
[:SOURce]:LIST:COPY[:CW]
[:SOURce]:LIST:DISPlay <numeric_value> | DEFault | MINimum | MAXimum
[:SOURce]:LIST:DWELl <numeric_value> {PS | NS | US | MS | S | MIN | HR} | DEFault | MINimum | MAXimum
[:SOURce]:LIST:FREQuency:POINts?
[:SOURce]:LIST:MODE <SWEep|POINt|AUTO|MANual>
[:SOURce]:LIST:POWer:POINts?
[:SOURce]:LIST:PRESet:ALL
[:SOURce]:PM:BWIDth <MINimum|MAXimum>
[:SOURce]:PM:ERRor?
[:SOURce]:PM[:EXTernal]:SENSitivity <numeric_value> | DEFault | MINimum | MAXimum
[:SOURce]:PM[:INTernal]:DEViation <numeric_value> | DEFault | MINimum | MAXimum
[:SOURce]:PM[:INTernal]:FREQuency <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:PM[:INTernal]:WAVE <SINE|GAUSsian|RDOWn|RUP|SQUare|TRIangle|UNIForm>
[:SOURce]:PM:MODE <LNOise|WDEViation>
[:SOURce]:PM:SOURce <INTernal|EXTernal>
[:SOURce]:PM:STATe <0 | 1 | ON | OFF>
[:SOURce]:POWer:ALC:SEARch:LNOise [<[ONCE]>]
[:SOURce]:POWer:ALC:SOURce <INTernal|DIODe|DIODe1|DIODe2|FIXed>
[:SOURce]:POWer:ATTenuation <numeric_value> {DB}
[:SOURce]:POWer:ATTenuation:AUTO <0 | 1 | ON | OFF>
[:SOURce]:POWer:CENTer <numeric_value> {<amplitude_units>} | DEFault | MINimum | MAXimum
[:SOURce]:POWer:DISPlay:OFFSet <numeric_value> {DB} | DEFault | MINimum | MAXimum
[:SOURce]:POWer:DISPlay:OFFSet:STATe <0 | 1 | ON | OFF>
[:SOURce]:POWer[:LEVel]:DAC <numeric_value> | DEFault | MINimum | MAXimum
[:SOURce]:POWer[:LEVel][:IMMediate][:AMPLitude] <numeric_value> {<amplitude_units>} | DEFault | MINimum | MAXimum | UP | DOWN
[:SOURce]:POWer[:LEVel][:IMMediate][:AMPLitude]:L<n> <numeric_value> {<amplitude_units>} | DEFault | MINimum | MAXimum
[:SOURce]:POWer[:LEVel][:IMMediate][:AMPLitude]:SELect <L0|L1|L2|L3|L4|L5|L6|L7|L8|L9>
[:SOURce]:POWer[:LEVel][:IMMediate][:AMPLitude]:STEP[:INCRement] <numeric_value> {DB} | DEFault | MINimum | MAXimum
[:SOURce]:POWer[:LEVel]:RANGe <HIGH|LOW>
[:SOURce]:POWer:LIMit[:AMPLitude] <numeric_value> {<amplitude_units>} | DEFault | MINimum | MAXimum | UP | DOWN
[:SOURce]:POWer:LIMit:STATe <0 | 1 | ON | OFF>
[:SOURce]:POWer:MODE <CW|FIXed|SWEep{2}|LIST{[1]}|LIST{2}|LIST{3}|LIST{4}|LIST{5}|LIST{6}|LIST{7}|LIST{8}|LIST{9}|LIST{10}>
[:SOURce]:POWer:PROTection:CLEar
[:SOURce]:POWer:PROTection:TRIPped?
[:SOURce]:POWer:SLOPe <numeric_value> | DEFault | MINimum | MAXimum | UP | DOWN
[:SOURce]:POWer:SLOPe:STATe <0 | 1 | ON | OFF>
[:SOURce]:POWer:SLOPe:STEP[:INCRement] <numeric_value> | DEFault | MINimum | MAXimum
[:SOURce]:POWer:SPAN <numeric_value> {DB} | DEFault | MINimum | MAXimum
[:SOURce]:POWer:SPAN:FULL
[:SOURce]:POWer:STARt <numeric_value> {<amplitude_units>} | DEFault | MINimum | MAXimum
[:SOURce]:POWer:STOP <numeric_value> {<amplitude_units>} | DEFault | MINimum | MAXimum
[:SOURce]:PULM:ERRor? [DEFault | MINimum | MAXimum]
[:SOURce]:PULM[:INTernal]:FREQuency <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:PULM:POLarity <NORMal|INVerted>
[:SOURce]:PULM:SOURce <INTernal|EXTernal>
[:SOURce]:PULM:STATe <0 | 1 | ON | OFF>
[:SOURce]:PULSe:COUNt <numeric_value> | DEFault | MINimum | MAXimum
[:SOURce]:PULSe:DELay<n> <numeric_value> {PS | NS | US | MS | S | MIN | HR} | DEFault | MINimum | MAXimum
[:SOURce]:PULSe:PERiod <numeric_value> {PS | NS | US | MS | S | MIN | HR} | DEFault | MINimum | MAXimum
[:SOURce]:PULSe:WIDTh<n> <numeric_value> {PS | NS | US | MS | S | MIN | HR} | DEFault | MINimum | MAXimum
[:SOURce]:ROSCillator:GPS:LOCK?
[:SOURce]:ROSCillator:HFRequency:BWIDth <WIDE|NARRow>
[:SOURce]:ROSCillator:HFRequency:LOCK?
[:SOURce]:ROSCillator:HFRequency:SOURce?
[:SOURce]:ROSCillator:LFRequency:SOURce?
[:SOURce]:ROSCillator:LOCK?
[:SOURce]:ROSCillator:MULTiplied:SOURce?
[:SOURce]:ROSCillator:RUBidium:LOCK?
[:SOURce]:ROSCillator:RUBidium:STATe <0 | 1 | ON | OFF>
[:SOURce]:ROSCillator:SOURce?
[:SOURce]:ROSCillator:SOURce:CURRent?
[:SOURce]:SWEep<n>:DIRection <UP|DOWN>
[:SOURce]:SWEep<n>:DWELl <numeric_value> {PS | NS | US | MS | S | MIN | HR} | DEFault | MINimum | MAXimum
[:SOURce]:SWEep<n>:DWELl:AUTO?
[:SOURce]:SWEep<n>:ERRor? [DEFault | MINimum | MAXimum]
[:SOURce]:SWEep<n>:GENeration <ANALog|STEPped>
[:SOURce]:SWEep<n>:POINts <numeric_value> | DEFault | MINimum | MAXimum
[:SOURce]:SWEep<n>:RANGe <F1F2|F3F4|F5DF|F6DF|L1L2|L3L4|L5L6|L7L8|L9L0>
[:SOURce]:SWEep<n>:TIME <numeric_value> {PS | NS | US | MS | S | MIN | HR} | DEFault | MINimum | MAXimum
[:SOURce]:SWEep<n>:TIME:AUTO?
[:SOURce]:SWEep<n>:TIME:LLIMit <numeric_value> {PS | NS | US | MS | S | MIN | HR} | DEFault | MINimum | MAXimum
[:SOURce]:SWEep[:FREQuency]:STEP <numeric_value> {HZ | KHZ | MHZ | GHZ} | DEFault | MINimum | MAXimum
[:SOURce]:SWEep<n>:POWer:STEP <numeric_value> {DB} | DEFault | MINimum | MAXimum
[:SOURce]:SWEep:SPACing <LINear|LOGarithmic>
:SYSTem:LANGuage
:SYSTem:LANGuage:NATive:CATalog?
:SYSTem:PRESet:REFerence:STATe <0 | 1 | ON | OFF>
:SYSTem:VERSion?
:TRIGger[:IMMediate]
:TRIGger:MODE <SWEep|POINt>
:TRIGger:SEQuence<n>:SLOPe <POSitive|NEGative>
:TRIGger:SEQuence<n>:SOURce <EXTernal{[1]|2}>
:TRIGger:SEQuence<n>:TYPE <FREerun|GATed|DELayed|TRIGgered|TRGDelay|COMPosite>
:TRIGger:SOURce <BUS|IMMediate|EXTernal>
:TRIGger:TYPE <AUTO|SINGle|EXTernal|MANual>
:TSWeep
:UNIT:FREQuency <HZ>
:UNIT:POWer <DBM|DBUV|V>
:UNIT:TIME <S>
Error Messages
Introduction
Error Query
Error Queue
Error Codes
No Error
Command Errors
Execution Errors
Device-Specific Errors
Query Errors
Parser Errors
Self-Test Messages
Command Reference
Rubidium™ RF/Microwave Signal Generator
Command Reference